Datasheet > A214S1MNMCB

A214S1MNMCB

更新时间： 2024-01-22 04:57:12

品牌	Logo	应用领域
埃梯梯 - ITT		开关驱动光电二极管
页数	文件大小	规格书
5页	338K
描述
Rotary Switch, 2 Positions, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Screw Driver Slot Actuator, Through Hole-straight, ROHS COMPLIANT

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

A214S1MNMCB 技术参数

是否无铅：	不含铅	是否Rohs认证：	符合
生命周期：	Active	包装说明：	ROHS COMPLIANT
Reach Compliance Code：	compliant	ECCN代码：	EAR99
HTS代码：	8536.50.90.20	执行器类型：	SCREW DRIVER SLOT
其他特性：	PANEL MOUNTABLE	主体高度：	12.83 mm
主体长度或直径：	26.19 mm	触点（交流）最大额定R负载：	.02A@20VAC
最大触点电流（交流）：	0.02 A	最大触点电流（直流）：	0.02 A
触点（直流）最大额定R负载：	.02A@20VDC	最大触点电压（交流）：	20 V
最大触点电压（直流）：	20 V	电气寿命：	15000 Cycle(s)
分度角：	90 deg	JESD-609代码：	e4
安装特点：	THROUGH HOLE-STRAIGHT	位置数：	2
开关段数量：	2	最高工作温度：	85 °C
最低工作温度：	-30 °C	表面贴装：	NO
开关动作：	LATCHED	开关功能：	DPDT
开关类型：	ROTARY SWITCH	端子面层：	Gold (Au) - with Nickel (Ni) barrier
端接类型：	SOLDER	Base Number Matches：	1

A214S1MNMCB 数据手册

C&K A Series

1-4 Pole Rotary Switches

FUNCTION

NONE NO SEAL

EPOXY SEAL

SPLASHPROOF BUSHING SEAL

EPOXY & SPLASHPROOF BUSHING SEAL

SPLASHPROOF

BUSHING SEAL

Setting Stops on A112 and A125 Models

The number of switch positions is adjustable on A112

and A125 models only by means of a stop ring provided

with each switch. The number of positions is pre-set on

all other models and the stop ring is factory installed.

To set stops: Turn shaft fully counter-clockwise and

insert stop ring tab in desired hole. Install lockwasher

and nut to retain stop ring for both PC and panel

mounting. Switch without stop ring has 12 positions.

Soldering, Cleaning and Assembly Instructions for ‘MC’ Termination Option

Soldering

Cleaning

1. Insert switch base only into PC board.

2. Do not bend terminals.

3. Wave soldering recommended at

500F solder temperature.

4. Hand solder at 500F, 10 sec.

max./terminal.

1. Flux clean using vapor degreaser and forced

rinse or triple bath method.

2. Do not allow switch base to ‘trap’ fluids.

3. Freon TMC, TF or Methylene Chloride give

excellent results.

REMOVABLE CLIP

Switch Assembly

1. Hold housing/shaft assembly by housing. Remove

protective cap by squeezing tabs and discard. (FIG. 1)

2. Do not push on switch shaft. Detent mechanism will

come apart.

3. While holding switch housing, align locating tab on

base with notch on housing and engage 4 housing

latches in slots on base. (FIG. 2)

(FIG. 1)

LOCATING

TA B

4. Push firmly on housing until latches snap in place.

5. Remove clip from shaft and discard. Assembly is

complete. (FIG. 3)

STANDOFF

(FIG. 2)

(FIG. 3)

AVAILABLE HARDWARE

Stop ring

PART NO.

767B00201

Material: Brass

Finish: Nickel plated

Dimensions are shown: Inch (mm)

Specifications and dimensions subject to change

www.ittcannon.com

L–7

1 2 3 45

下载PDF

与A214S1MNMCB相关器件

型号	品牌	描述	获取价格	数据表
A214S1MNMCBE	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Screw Driver Slo	获取价格
A214S1MNMCBF	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Screw Driver Slo	获取价格
A214S1MNMCBK	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.02A, 20VDC, Solder Terminal, Screw Driver Slo	获取价格
A214S1MNMCG	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.35A, 125VDC, Solder Terminal, Screw Driver Sl	获取价格
A214S1MNMCGE	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.35A, 125VDC, Solder Terminal, Screw Driver Sl	获取价格
A214S1MNMCGF	ITT	Rotary Switch, 2 Positions, DPDT, Latched, 0.35A, 125VDC, Solder Terminal, Screw Driver Sl	获取价格

与A214S1MNMCB相关文章

SI2301 N沟道MOSFET：资料手册参数分析
2024-05-08

4
ADC0809逐次逼近寄存器型模数转换器：资料手册参数分析
2024-05-08

4
AD9361捷变收发器：全面参数解析与关键特性概览
2024-05-08

2
IRF3205功率MOSFET：资料手册参数分析
2024-05-08

2

产品中心

服务支持

精选活动

关于我们

帮助中心

A214S1MNMCB

A214S1MNMCB 技术参数

A214S1MNMCB 数据手册

与A214S1MNMCB相关器件

与A214S1MNMCB相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

A214S1MNMCB

A214S1MNMCB 技术参数

A214S1MNMCB 数据手册

与A214S1MNMCB相关器件

与A214S1MNMCB相关文章

您还可以找

您在本页遇到什么问题？