A1101, A1102, A1103, A1104, and A1106
Continuous-Time Switch Family
Functional Description
OPERATION
continuous-time devices typically require programming after
packaging to tighten magnetic parameter distributions. In con-
trast, chopper-stabilized switches employ an offset cancellation
technique on the chip that eliminates these offsets without the
need for after-packaging programming. The tradeoff is a longer
settling time and reduced frequency response as a result of the
chopper-stabilization offset cancellation algorithm.
The output of these devices switches low (turns on) when a
magnetic field (south polarity) perpendicular to the Hall sen-
sor exceeds the operate point threshold, BOP. After turn-on, the
output is capable of sinking 25 mA and the output voltage is
VOUT(SAT). When the magnetic field is reduced below the release
point, BRP, the device output goes high (turns off). The differ-
ence in the magnetic operate and release points is the hysteresis,
The choice between continuous-time and chopper-stabilized
designs is solely determined by the application. Battery manage-
ment is an example where continuous-time is often required. In
these applications, VCC is chopped with a very small duty cycle
in order to conserve power (refer to figure 2). The duty cycle
is controlled by the power-on time, tPO, of the device. Because
continuous-time devices have the shorter power-on time, they
are the clear choice for such applications.
Bhys, of the device. This built-in hysteresis allows clean switch-
ing of the output, even in the presence of external mechanical
vibration and electrical noise.
Powering-on the device in the hysteresis region, less than BOP
and higher than BRP, allows an indeterminate output state. The
correct state is attained after the first excursion beyond BOP or
BRP.
For more information on the chopper stabilization technique,
refer to Technical Paper STP 97-10, Monolithic Magnetic Hall
Sensor Using Dynamic Quadrature Offset Cancellation and
Technical Paper STP 99-1, Chopper-Stabilized Amplifiers with a
Track-and-Hold Signal Demodulator.
CONTINUOUS-TIME BENEFITS
Continuous-time devices, such as the A110x family, offer the
fastest available power-on settling time and frequency response.
Due to offsets generated during the IC packaging process,
(A)
(B)
VS
V+
VCC
VCC
RL
Sensor Output
A110x
VOUT
GND
VOUT(SAT)
B+
0
B–
0
BHYS
Figure 1. Switching Behavior of Unipolar Switches. On the horizontal axis, the B+ direction indicates increasing south polarity magnetic field
strength, and the B– direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This behavior can
be exhibited when using a circuit such as that shown in Panel B.
Allegro MicroSystems, Inc.
7
115 Northeast Cutoff, Box 15036
A1101-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
5秒后页面跳转
电子元器件中的网络滤波器、EMI滤波器与EMC滤波器：分类关系与功能详解
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
