700HBAW_1.5 series
700W Half-Brick - Single Output DC-DC Converter - Wide Input - Isolated & Regulated
DC-DC Converter
700 Watt
Compliance with RoHS6 EU
Directive 2011/65/EU
Delivers up to 25A output current
High efficiency, typ.94% at
48Vin half load
Low output ripple and noise
Exceptional thermal performance
Industry standard “Half-brick“
footprint
Fixed switching frequency
(270 kHz typical)
Remote Sense
The 700HBAW_1.6 series are half-brick DC/DC converters that provide
high efficiency single output. They can operate from 36VDC to 75VdD-
Cinput and 28V/25A output. The output can be trimmed from
(14VDC~33Vdc) of normal output voltage. The remote control option is
positive logic. The converter turns on when the REM pin is at logic high
and turns off when it at logic low, both are referenced to -Vin. The
converter is on when the REM pin is left open. The output voltage trim
option is positive. The output voltage will increase when the TRIM pin
connected to +S pin and decrease when it connected to -S pin. The
output voltage will increase when the TRIM pin connected to +S pin and
decrease when it connected to -S pin.
Input under voltage lockout
Output over voltage protection
Over temperature protection
Output over current protection
Adjustable output voltage
(14VDC~33VDC)
Meets the voltage and current
requirements for ETSI 300-132-2
and complies with and licensed
for Basic Insulation rating per
IEC60950-1
Output specifications
Output specifications
Item
Test condition
Min Typ Max
4
Units
h
Item
Test condition
Min
27.6
Typ Max
Units
VDC
A
Short circuit protection Hiccup Mode
Voltage set point Vin=Vin(nom); Io=Io(max)
Output Current
28
28.4
25
1
Automatic recovery
Efficiency
Vin=48V, 100%load
ambient temperature 25°C
91
92
93
94
%
%
Line regulation
Vin=Vin(min) to Vin(max)
lo= lo(max)
0.4
%
Operating temp
Base Plate
-40
-40
-55
100
85
°C
Load regulation
Io=0 to Io(max);Vin=Vin(nom)
0.4
28
1
%
Ambient Temperature
Storage temperature
Operating Humidity
Storage Humidity
Operating Altitude
Storage Altitude
°C
Total Output
Voltage Range
Over sample, line, load,
temperature & life
27.2
14
28.8
VDC
125
°C
90
%RH
%RH
m
Output Voltage
Precision
Vin=Vin(min) to Vin(max)
Io=0 to Io(max)
1.5
3
%Vo
VDC
%Vo
A
90
Output Voltage
Adj. Range
Rated power Po=0~700W
see figure 11 and 12
33
10
37.5
0
0
3000
3000
m
Remote Sense
Compensation
Switching
Frequency
Vin=Vin(nom); Io=Io(max);
Fixed frequency
220 270 320
kHz
Output current
limit inception
Ambient Temperature 25°C,
Hiccup mode Automatic recovers
26.5
MTBF
Telcordia SR332, 40°C Ta
109/MTBF
2,800,000
357
h
External load
capacitance
ESR<200mΩ at -40°C, recommend 1100
2~3PCS KY, KZE and KZH series
aluminum capacitors in parallel
4400 µF
FIT
Thermal Stability Time
Weight
-
30
95
min
g
85
105
Temperature
coefficient
Ambient Temperature -40°C ~85°C
200
ppm
/°C
Safety
Compliant to IEC60950-1,UL60950-1,EN60950-1,GB4943
Dynamic
response
25%-50%-25%&50%-75%-50%
Io(max) di/dt=0.1A/µS
• Overshoot Range
Vibration
IEC60068-2-6:10-500Hz sweep,0.75mm excursion,10g
acceleration, 10min in each 3 perpendicular directions
350 700
mV
µS
Transportation
Shock
ETS300019-1-2
• Recovery Time
100
500
IEC60068-2-27:200g acceleration, duration 3 ms,6 drops
in each 3 perpendicular directions
Ripple & Noise
Measured with 10µF Tantalum
external and 1µF ceramic
capacitor at output, 100%load,
20MHz bandwidth
100
50
250
100
mVp-p
mVRM
S
Input specifications
Item
Test condition
Min Typ Max Units
Turn-on delay
time
Time from instant at which
Vin=Vin(min) until Vo=10% of
Vo(nom)
200
400 800
ms
Input voltage
• Continuous
• Transient (100ms)
80
100
VDC
VDC
Turn-on Rise
Time
Time for Vo to rise from 10% of
Vo(nom) to 90% of Vo(nom)
100
300
ms
Operating Input Voltage
Max. Input Current
36
48
75
VDC
A
100% load Vin=36V
No load Full Input Voltage
mA
22.5
Turn off Fall
Time
From Vo drop point to drop to
10V,Io=0A
• Cout=1000uF
• Cout=4400uF
No load Input Current
Standby Input Current
200 mA
100
400 600
5
200
ms
ms
10
100
mA
mA
Input Reflected Ripple
Current Peak-to-Peak
12 µH source impedance,
add 470µFelectrolytic and
1µF ceramic capacitor at
input
150 300
Output Voltage
Overshoot
%Vo
Example:
Recommended External
Input Capacitance
Low ESR capacitor
recommended
470
µF
700HBAW_4848S1.5
W = 700 Watt; HB = Half-Brick; A = Pinning; W = Wide input (2:1);
48 = 36-72 Vin; 48 = 48Vout; S = Single Output; 1.5 = 1.5kVDC Isolation
Filter Component Value
Inrush Transient
Input fuse
14/0.33
µF/uH
AꢀS
A
1
40
Page 1 of 8
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
700HBAW_1.5 – Rev. 2020-1.0
Specifications subject to change without notice.