5.0 Absolute Maximum Ratings for
the LM311(Note 12)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 10 sec)
Voltage at Strobe Pin
0˚ to 70˚C
−65˚C to 150˚C
260˚C
V+−5V
Soldering Information
Dual-In-Line Package
Total Supply Voltage (V84
)
36V
40V
30V
30V
15V
Soldering (10 seconds)
Small Outline Package
260˚C
Output to Negative Supply Voltage (V74
)
Ground to Negative Supply Voltage (V14
Differential Input Voltage
)
Vapor Phase (60 seconds)
Infrared (15 seconds)
215˚C
220˚C
±
±
Input Voltage (Note 13)
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
Power Dissipation (Note 14)
ESD Rating (Note 19)
500 mW
300V
Output Short Circuit Duration
10 sec
Electrical Characteristics (Note 15)
for the LM311
Parameter
Input Offset Voltage (Note 16)
Input Offset Current(Note 16)
Input Bias Current
Conditions
TA=25˚C, RS≤50k
TA=25˚C
Min
Typ
2.0
Max
7.5
50
Units
mV
nA
6.0
TA=25˚C
100
200
200
0.75
250
nA
Voltage Gain
TA=25˚C
40
V/mV
ns
Response Time (Note 17)
Saturation Voltage
TA=25˚C
VIN≤−10 mV, IOUT=50 mA
1.5
5.0
50
V
TA=25˚C
TA=25˚C
Strobe ON Current (Note 18)
Output Leakage Current
2.0
0.2
mA
nA
VIN≥10 mV, VOUT=35V
TA=25˚C, ISTROBE=3 mA
V− = Pin 1 = −5V
RS≤50K
Input Offset Voltage (Note 16)
Input Offset Current (Note 16)
Input Bias Current
10
70
mV
nA
nA
V
300
13.0
0.4
Input Voltage Range
−14.5
13.8,−14.7
0.23
Saturation Voltage
V+≥4.5V, V−=0
V
VIN≤−10 mV, IOUT≤8 mA
Positive Supply Current
Negative Supply Current
TA=25˚C
TA=25˚C
5.1
4.1
7.5
5.0
mA
mA
Note 12: “Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.”
±
Note 13: This rating applies for 15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the
negative supply voltage or 30V below the positive supply, whichever is less.
Note 14: The maximum junction temperature of the LM311 is 110˚C. For operating at elevated temperature, devices in the H08 package must be derated based
on a thermal resistance of 165˚C/W, junction to ambient, or 20˚C/W, junction to case. The thermal resistance of the dual-in-line package is 100˚C/W, junction to
ambient.
±
<
<
T +70˚C, unless otherwise specified. The offset voltage, offset current and
A
±
Note 15: These specifications apply for V
=
15V and Pin 1 at ground, and 0˚C
S
bias current specifications apply for any supply voltage from a single 5V supply up to 15V supplies.
Note 16: The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1 mA load. Thus, these
parameters define an error band and take into account the worst-case effects of voltage gain and R .
S
Note 17: The response time specified (see definitions) is for a 100 mV input step with 5 mV overdrive.
Note 18: This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled. Do not short the strobe
pin to ground; it should be current driven at 3 to 5 mA.
Note 19: Human body model, 1.5 kΩ in series with 100 pF.
www.national.com
4