1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
X
Y
4
5
6
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
8
8
5
5
5
Flat pack with gull wing leads, glass sealed
Flat pack with straight leads, glass sealed
MO-078 with straight leads, glass sealed
MO-078 with leads bent down, glass sealed
MO-078 with leads bent up, glass sealed
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Supply voltage (VCC)..................................................................
Output current (IOUT) ..................................................................
Junction temperature (TJ) ..........................................................
Power Stage Thermal Resistance(RθJ-C) ..................................
Storage temperature..................................................................
Lead temperature (soldering, 10 seconds) ................................
0 V dc to +8.0 V dc
3 A
+150°C
1°C/W
-65°C to +150°C
+300°C
1.4 Recommended operating conditions.
Supply voltage range (VCC
)
Device types 01, 03, 04..........................................................
Device types 02, 05................................................................
Case operating temperature range (TC).....................................
+2.97 V dc to +3.8 V dc
+3.8 V dc to +5.8 V dc
-55°C to +125°C
1.5 Radiation features.
Maximum total dose available (dose rate = 50 - 300 rads(Si)/s)
Maximum total dose available (dose rate ≤ 10 mrads(Si)/s) LDR:
Neutron Irradiation (1 MeV equivalent neutrons).......................
300 krads (Si)
100 krads(Si) 2/
≥ 1.0 X 1011 (n/cm2) 3/
Single event phenomenon (SEP) effective linear energy threshold (LET):
SEL, SEFI...............................................................................
>84 MeV-cm2/mg 4/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
2/ The devices have been tested for Enhanced Low Dose Rate Sensitivity (ELDRS) in accordance with method 1019
paragraph 3.13.1.1 of MIL-STD-883 initial qualification. No ELDRS was observed. The devices will be re-tested after
design or process changes that can affect RHA response of these devices.
3/ The measured neutrons to gamma ratio for the Fast Neutron, Irradiator facility at UMass, Lowell is 3.69 X 109 n/cm2 per
rad(Si).
4/ Single event performance is tested with minor transients only; no dropouts, shutdowns, latch up or burn out.
SIZE
STANDARD
5962-10235
A
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
REVISION LEVEL
A
SHEET
COLUMBUS, OHIO 43218-3990
3
DSCC FORM 2234
APR 97
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
