R
QPRO XQ4000XL Series QML High-Reliability FPGAs
XQ4000XL Switching Characteristics
Definition of Terms
In the following tables, some specifications may be designated as Advance or Preliminary. These terms are defined as
follows:
Advance:
Initial estimates based on simulation and/or extrapolation from other speed grades, devices, or
devicefamilies. Values are subject to change. Use as estimates, not for production.
Preliminary: Based on preliminary characterization. Further changes are not expected.
Unmarked: Specifications not identified as either Advance or Preliminary are to be considered Final.
Except for pin-to-pin input and output parameters, the a.c. parameter delay specifications included in this document are
derived from measuring internal test patterns. All specifications are representative of worst-case supply voltage and junction
temperature conditions.
All specifications subject to change without notice.
Additional Specifications
Except for pin-to-pin input and output parameters, the a.c.
parameter delay specifications included in this document
are derived from measuring internal test patterns. All speci-
fications are representative of worst-case supply voltage
and junction temperature conditions. The parameters
included are common to popular designs and typical appli-
cations. For design considerations requiring more detailed
timing information, see the appropriate family AC supple-
ments available on the Xilinx web site at:
http://www.xilinx.com/partinfo/databook.htm.
Absolute Maximum Ratings(1)
Symbol
Description
Units
V
Supply voltage relative to GND
–0.5 to 4.0
–0.5 to 5.5
–0.5 to 5.5
50
V
V
CC
(2)
V
Input voltage relative to GND
IN
(2)
V
Voltage applied to High-Z output
V
TS
V
T
Longest supply voltage rise time from 1V to 3V
Storage temperature (ambient)
ms
°C
°C
°C
°C
CCt
–65 to +150
+260
STG
SOL
T
Maximum soldering temperature (10s @ 1/16 in. = 1.5 mm)
T
Junction temperature
Ceramic package
Plastic package
+150
J
+125
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress
ratings only, and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions
is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods of time may affect device reliability.
2. Maximum DC overshoot or undershoot above V or below GND must be limited to either 0.5V or 10 mA, whichever is easier to
CC
achieve. During transitions, the device pins may undershoot to –2.0 V or overshoot to V + 2.0V, provided this over- or undershoot
CC
lasts less than 10 ns and with the forcing current being limited to 200 mA.
Recommended Operating Conditions(1)
Symbol
Description
Min
Max
3.6
Units
V
Supply voltage relative to GND, T = –55°C to +125°C Plastic
3.0
V
V
CC
J
Supply voltage relative to GND, T = –55°C to +125°C Ceramic
3.0
3.6
C
(2)
V
High-level input voltage
50% of V
5.5
V
IH
CC
V
Low-level input voltage
0
-
30% of V
250
V
IL
CC
T
Input signal transition time
ns
IN
Notes:
1. At junction temperatures above those listed as Operating Conditions, all delay parameters increase by 0.35% per °C.
2. Input and output measurement threshold is ~50% of V
.
CC
DS029 (v1.3) June 25, 2000
www.xilinx.com
3
Product Specification
1-800-255-7778
5秒后页面跳转
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
74HC573三态非易失锁存器(Latch)资料手册参数分析
MAX3232 RS-232电平转换器资料手册参数分析
MAX485 RS-485/RS-422收发器资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
