AD827
AD827J
Min Typ Max
AD827A/S
Min Typ Max
Model
Conditions
VS
Units
OUTPUT RESISTANCE
Open Loop
15
15
Ω
POWER SUPPLY
Operating Range
Quiescent Current
±4.5
±18
13
16
±4.5
±18
13
16.5/17.5
V
±5 V
10
10
mA
mA
mA
mA
T
MIN to TMAX
±15 V
10.5 13.5
16.5
10.5 13.5
17/18
TMIN to TMAX
TRANSISTOR COUNT
92
92
NOTES
1Offset voltage for the AD827 is guaranteed after power is applied and the device is fully warmed up. All other specifications are measured using high speed test equip-
ment, approximately 1 second after power is applied.
2Full Power Bandwidth = Slew Rate/2 π VPEAK
.
3Gain = +1, rising edge.
All min and max specifications are guaranteed.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS1
ORDERING GUIDE
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Internal Power Dissipation2
Temperature
Range
Package
Description
Package
Option
Model
Plastic (N) Package (Derate at 10 mW/°C) . . . . . . . . 1.5 W
Cerdip (Q) Package (Derate at 8.7 mW/°C) . . . . . . . . 1.3 W
Small Outline (R) Package (Derate at 10 mW/°C) . . . 1.5 W
LCC (E) Package (Derate at 6.7 mW/°C) . . . . . . . . . 1.0 W
Input Common Mode Voltage . . . . . . . . . . . . . . . . . . . . . .±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Output Short Circuit Duration3 . . . . . . . . . . . . . . . . Indefinite
Storage Temperature Range (N, R) . . . . . . . –65°C to +125°C
Storage Temperature Range (Q) . . . . . . . . . –65°C to +150°C
Operating Temperature Range
AD827JN
AD827JR
AD827AQ
AD827SQ
AD827SQ/883B
0°C to +70°C
0°C to +70°C
–40°C to +85°C
–55°C to +125°C 8-Pin Cerdip
–55°C to +125°C 8-Pin Cerdip
8-Pin Plastic DIP N-8
16-Pin Plastic SO R-16
8-Pin Cerdip
Q-8
Q-8
Q-8
Q-8
E-20A
E-20A
5962-9211701MPA –55°C to +125°C 8-Pin Cerdip
AD827SE/883B –55°C to +125°C 20-Pin LCC
5962-9211701M2A –55°C to +125°C 20-Pin LCC
AD827JR-REEL
AD827JChips
AD827SChips
0°C to +70°C
0°C to +70°C
–55°C to +125°C Die
Tape & Reel
Die
AD827J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
AD827A . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
AD827S . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
Lead Temperature Range
METALIZATION PHOTOGRAPH
Contact factory for latest dimensions.
Dimensions shown in inches and (mm).
Substrate is connected to V+.
(Soldering to 60 sec) . . . . . . . . . . . . . . . . . . . . . . . +300°C
NOTES
1Stresses above those listed under “Absolute Maximum Ratings” may cause
permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied. Exposure to absolute
maximum ratings for extended periods may affect device reliability.
2Maximum internal power dissipation is specified so that TJ does not exceed
+175°C at an ambient temperature of +25°C.
Thermal Characteristics:
Mini-DIP: θJA = 100°C/Watt; θJC = 33°C/ Watt
Cerdip: θJA = 110°C/Watt; θJC = 30°C/Watt
16-Pin Small Outline Package: θJA = 100°C/Watt
20-Pin LCC: θJA = 150°C/Watt; θJC = 35°C/Watt
3Indefinite short circuit duration is only permissible as long as the absolute
maximum power rating is not exceeded.
REV. B
–3–