Instruction Sheet
PRO-CRIMPER* III Hand
Crimping Tool Assembly And
Die Set 58517-[ ]
408-4064
10 MAY 12 Rev F
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Locator
(Supplied with
Die Assembly)
Stationary Jaw
Back of Tool
(Wire Side)
Pivot Pin
Front of Tool
(Locator Side)
PRO-CRIMPER III
Hand Crimping
Tool Frame
354940-1
(Instruction
Moving Jaw
Die Assembly
Sheet 408-9930)
Ratchet Adjustment Wheel
The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade tool
and is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate Application Specification (114-series), but may not comply
with other feature parameters of the specification. TE Connectivity offers a
variety of tools to satisfy your performance requirements. For additional
information, contact the Tooling Assistance Center at 1-800-722-1111.
Handle
Moving
Jaw
WIRE
LOCATOR
PART
NUMBER‡
PRO-CRIMPER DIE ASSEMBLY
CONTACT
FAMILY
SIZE
(AWG)
INSUL DIA
(mm [in.])
STRIP LENGTH
III HAND TOOL
PART NUMBER
(mm [in.])
58517-1
58517-3
None
58517-2
58517-4
58517-5 •
189590-1
1424907-1
1901843-1
CST 100
CST 100 II
CST 100 II
0.89-1.65
[.035-.065]
2.54-2.92
[.100-.125]
26-22
• Bench Machine/Battery and
SDE-SA Hand Tool Only
‡ Supplied with the die assembly. Also available
separately.
‡‡ Contact the PRODUCT INFORMATION CENTER for specific contact part
numbers.
Figure 1
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
1. INTRODUCTION
PRO-CRIMPER III Hand Crimping Tool Assembly
58517-1 consists of Die Assembly 58517-2 and
PRO-CRIMPER III Hand Tool Frame 354940-1. See
Figure 1.
2. DESCRIPTION (See Figure 1 and Figure 2.)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The die assembly consists of crimping dies and a
locator assembly.
The tool frame holds a die assembly with one crimping
section.
Read these instructions thoroughly before crimping
any contacts.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures and
NOTE
illustrations are for identification only and are not
drawn to scale.
Attached to the outside of the frame is a locator, which
holds and helps to position the contact.
i
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 5
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
5秒后页面跳转
全球首块英伟达H200交付 黄仁勋“送货上门”
常用8脚开关电源芯片型号大全
74HC04芯片引脚图及功能、应用电路图讲解
CR6842芯片参数、引脚配置、应用电路图详解
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
