AMP Dynamic Series Connectors
D-5200 Series (Continued)
Receptacle Contact
(Used in Receptacle Housing)
Tab Contact
(Used in Tab Housing)
Crimp Type Contacts
D-5 Contacts
Ins. Dia. Wire
Wire Range
Contact Part Numbers*
Application Tooling
Range
mm
Range
Mark
mm2
Receptacle
Tab
Sequential Tab Mini-Applicator
Hand Tool
AWG
16
1.25
2.20
3.50
5.50
ST.
LP.
ST.
LP.
84696-1
1,—
**
—
**
179955-J
316040-J
179956-J
316041-J
917802-J
917804-J
917803-J
917805-J
—
3~3.8
4~5.2
S
14
234170-1
—
12
84695-1
1—
M
10
—
234171-1
* Strip Form contacts are used with Mini-Applicator and Loose-Piece contacts
are with hand tools.
Note: Enter the following plating code in Part Number suffix-
:
J
-2 = 0.38 µm thick gold plating, -3 = 0.76µm thick gold plating,
-6 = 2.54 µm thick silver plating
**Mini-Applicator is for use on Automachines. (See next page. Contact
Technical Support for details.)
D-5α Contacts (Silver Plating)
Ins. Dia. Wire
Wire Range
Contact Part Numbers*
Application Tooling
Mini-Applicator Hand Tool
Range
mm
Range
AWG
20
mm2
Receptacle
1318985-6
1318986-6
0179955-6
0316040-6
0179956-6
0316041-6
1318696-6
1318697-6
Mark
0.50
1.25
1.25
2.20
3.50
5.50
ST.
LP.
ST.
LP.
ST.
LP.
ST.
LP.
**
—
**
—
91596-1
—
1.8~3.23
3~3.80
4~5.2
SS
16
16
S
M
L
14
—
**
234170-1
—
12
10
—
**
234171-1
—
8.00
8
4.9~7.8
—
1366044-1
Note: The contact part numbers with "-6" are silver plated with
* Strip Form contacts are used with Mini-Applicator and Loose-Piece contacts
are with hand tools.
2.54 µm thickness.
**Mini-Applicator is for use on Automachines. (See next page. Contact
Technical Support for details.)
Application Tooling
Extraction Tool
Part Number: 409158-1
Instruction Sheet 411-5774
•Used to extract contacts from wire type tab / receptacle housing.
(Take care when inserting tool as the lance section of D-5 is turned upside down to that of D-3.)
•With D-5 contacts only, it is possible to extract using a small-size slotted screwdriver.
• How to Use Extraction Tool
When Using D-5 Extraction Tool
When Using Slotted Screwdriver
The tip of Extraction Tool depresses
housing lance, freeing contact.
When you butt the tip of tool at lance
section and depress it, contact is
released.
Insert Extraction Tool in the direction
as shown, insert into the narrow lower
section of Housing’s reverse convex hole.
(make sure that you are holding tool in
proper position, top and bottom.)
Take care not to insert tool into contact
section. If you’ve inserted by error,
replace the contact with a new one
before proceeding.
*
Contact can be pulled out.
Contact can now be pulled out.
84
Catalog 1242132
Revised 5-07
Dimensions are in millimeters
unless otherwise specified.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
www.tycoelectronics.com
UK: 44-8706-080-208