DieleCTRiC
CHaRaCTeRiSTiCS
npo
x7R
TEMPERATURE COEFFICIENT:
QUALITY FACTOR / DF:
0
30ppm /°C, -55 to 125°C
15%, -55 to 125°C
Q
>1,000 @ 1KHz (C>1,000pF), Typical 10,000
16VDC Dp≤ 3.5% @ 1 KHz, 25°C
10VDC Dp≤ 5.0% @ 1 KHz, 25°C
(C<1,000 pF)
4
4
1
INSULATION RESISTANCE:
DIELECTRIC STRENGTH:
>500 ΩF or 10 GΩ @ 25°C,WVDC ;
1
>100 GΩ @ 25°C,WVDC ;
125°C IR is 10% of 25°C rating
125°C IR is 10% of 25°C rating
1
2.5 X WVDC Min., 25°C, 50 mA max
1
500 V ≤ 2.5 X WVDC Min., 25°C, 50 mA max
1000 V ≤ 1.5 X WVDC Min., 25°C, 50 mA max
> 1500 = 1 X WVDC Min., 25°C, 50 mA max
1KHz 50Hz, 1.0 0.2 VRMS, 25°C
100 - 10,000 pF
1
1
TEST PARAMETERS::
1MHz 50ꢀHz, 1.0 0.2 VRMS, 25°C
AVAILABLE CAPACITANCE:
Size 0201: 0.2 - 100 pF
Size 0402: 0.2 - 33 pF
Size 0603: 0.2 - 100 pF
Size 0805: 0.3 - 220 pF
Size 1111: 0.2 - 1000 pF
Size 2525: 1.0 - 2700 pF
Size 3838: 1.0 - 5100 pF
MECHANICAL & ENVIRONMENTAL
CHARACTERISTICS
SPECIFICATION
TEST PARAMETERS
SOLDERABILITY:
Solder coverage ≥ 90% of metalized areas
No termination degradation
Preheat chip to 120°-150°C for 60 sec., dip terminals in rosin flux
then dip in Sn62 solder @ 240° 5°C for 5 1 sec
RESISTANCE TO
SOLDERING HEAT:
No mechanical damage
Preheat device to 80°-100°C for 60 sec.
followed by 150°-180°C for 60 sec.
Dip in 260° 5°C solder for 10 1 sec.
Measure after 24 2 hour cooling period
Capacitance change: 2.5% or 0.25pF
Q>500 I.R. >10 G Ohms
DWV2: 2.5 x WVDC1
TERMINAL
ADHESION:
Termination should not pull off.
Ceramic should remain undamaged.
Linear pull force3 exerted on axial leads soldered to each terminal.
PCB DEFLECTION:
No mechanical damage.
Capacitance change: 2% or 0.5pF Max
Glass epoxy PCB: 0.5 mm deflection
LIFE TEST:
MIL-STD-202, Method 108l
No mechanical damage
Capacitance change: 3.0% or 0.3 pF
Q>500 I.R. >1 G Ohms
DWV2: 2.5 x WVDC1
Applied voltage: 200% of WVDC1 for capacitors rated at 500 volts DC or less.
100% of WVDC1 for capacitors rated at 1250 volts DC or less.
Temperature: 125° 3°C
Test time: 1000+48-0 hours
THERMAL CYCLE:
No mechanical damage.
5 cycles of: 30 3 minutes @ -55°+0/-3°C,
2-3 min. @ 25°C, 30 3 min. @ +125°+3/-0°C,
2-3 min. @ 25°C
Capacitance change: 2.5% or 0.25pF
Q>2000 I.R. >10 G Ohms
DWV2: 2.5 x WVDC1
Measure after 24 2 hour cooling period
HUMIDITY,
STEADY STATE:
No mechanical damage.
Relative humidity: 90-95%
Temperature: 40° 2°C
Test time: 500 +12/-0 Hours
Measure after 24 2 hour cooling period
Capacitance change: 5.0% or 0.50pF max.
Q>300 I.R. ≥ 1 G-Ohm
DWV2: 2.5 x WVDC1
HUMIDITY,
LOW VOLTAGE:
No mechanical damage.
Applied voltage: 1.5 VDC, 50 mA max.
Relative humidity: 85 2% Temperature: 40° 2°C
Test time: 240 +12/-0 Hours
Capacitance change: 5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohm min.
DWV2: 2.5 x WVDC1
Measure after 24 2 hour cooling period
VIBRATION:
No mechanical damage.
Capacitance change: 2.5% or 0.25pF
Q>1000 I.R. ≥ 10 G-Ohm
DWV2: 2.5 x WVDC1
Cycle performed for 2 hours in each of three perpendicular directions
Frequency range 10Hz to 55 Hz to 10 Hz traversed
in 1 minute. Harmonic motion amplitude: 1.5mm
1 - WVDC - Working Voltage DC.
2 - DWV - Dielectric Withstanding Voltage.
3 - 0402 ≥ 2.0lbs, 0603 ≥ 4.0lbs (min).
4 - Whichever is less.
10
www.johansontechnology.com
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
