Instruction Sheet
TNC COAXICON* Connector
Crimping Tools and Dies
408-2235
28 SEP 12 Rev C
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
BULKHEAD
JACK
RIGHT-ANGLE
PLUG
CRIMPING
TOOL
CRIMPING
DIES‡
CABLE
PLUG
JACK
331109
331109-1†
331109-2†
1-332292-7
1-332292-8†
1-332292-9†
331133
331133-1†
226484-1†
226484-2
RG 304
69811
220006-1
‡For use in Hand Tool 69710 or Pneumatic Tool 69365. †Engineering controlled.
Figure 1
3. Push crimp end back under braid so that the
braid passes over and around the support sleeve.
Apply sufficient pressure to cause the cable
dielectric to bottom against the dielectric of the
crimp end. See Figure 2. Twist the crimp end
slightly to ensure bottoming.
1. INTRODUCTION
The Series TNC Connectors listed in Figure 1 are
used with Hand Tool 69811, with Dies 220006-1 in
Hand Tool 69710, or Pneumatic Tool 69365.
2. CRIMP END ASSEMBLY
4. Slide the ferrule forward and over the braid on the
crimp end as far as it will go. Crimp end is now
ready to be crimped. See Figure 2.
1. Slip the ferrule on the cable, then strip the cable
and flair braid as shown in Figure 2.
2. Insert stripped conductor into the wire barrel on
the crimp end. Twist crimp end slightly to ease entry
of wire.
3. CRIMPING PROCEDURE
3.1. Hand Tool 69811
1. Open crimping dies by closing the tool handles
until the CERTI-CRIMP* hand crimping tool ratchet
control releases. Note that once the ratchet is
engaged, the handles cannot be opened until they
are fully closed.
Plug or Jack
11.13 [.438]
Crimp End
2.39
[.094]
11.13
[.438]
Braid Ferrule
Wire
Barrel
Support
Sleeve
2. The crimping tools have double sets of dies, see
Figure 3, to crimp the braid ferrule and wire barrel of
the jack or plug crimp end. Ferrule and wire barrel
are crimped at the same time.
Flared Braid Goes Over and
Around Support Sleeve
3. Place the crimp end in the crimping dies as
shown in Figure 3.
Crimp End Dielectric
Wire Barrel of Plug or
Jack Crimp End Will
Bottom in Crimping Die
Apply Sufficient Pressure to Cause
Cable Dielectric to Bottom Against
Dielectric of Crimp End
Cable Dielectric
Push Ferrule Over Braid, Ferrule
Bottoms Against Shoulder
Braid Ferrule Will
Bottom on Upper Braid
Ferrule Crimping Die
Shoulder
Assembly Now Ready
to be Crimped
Figure 3
Figure 2
©2012 Tyco Electronics Corporation, a TE Connectivity Ltd. company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change.
1 of 2
All Rights Reserved
*Trademark
PRODUCT INFORMATION 1-800-522-6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
