Instruction Sheet
Hydraulic Crimping Head
1752868-1
408-8959
22 MAR 10 Rev B
a piston (ram) which holds and controls the moving
die, and a quick--disconnect coupling (cylinder half)
which mates with the coupling on the hose to release
or supply pressure. A dust cap covers the
quick--disconnect coupling.
“C”-Head
Piston (Ram)
(Fully Extended)
3. INSTALLATION AND REMOVAL
3.1. Crimping Head
Prior to installing the crimping head, ensure that
the pump and hose being used are working
properly, and are adjusted to and rated at
10,000 psi. An incorrectly adjusted or rated
pump/hose could result in severe tooling
damage, as well as personal injury.
CAUTION
!
1. Release the hydraulic pressure to the hose.
Disconnect the electric power unit from the power
supply.
2. Remove the protective dust caps.
Quick-Disconnect
Coupling
3. Thoroughly clean the coupling on the
pump/hose and the coupling on the crimping head.
Dust Cap
4. Mate both the quick--disconnect couplings and
tighten the collar of the coupler assembly on the
hose.
Figure 1
Oil flow must be unobstructed between the power
unit and the crimping head. Ensure that all
couplings are fully mated and tightened.
CAUTION
1. INTRODUCTION
!
Hydraulic Crimping Head 1752868--1 shown in
Figure 1 accepts interchangeable die sets for a
variety of terminals and splices that accept wire sizes
12 through 350 MCM. Refer to the instructions
packaged with the specific die set for compatible
products, wire ranges, strip dimensions, and
application procedures.
If a crimping head must be removed after the
power unit was in operation, be sure to release
the pressure in the hydraulic system. When using
Hydraulic Power Unit 1804700 -[ ],
DISCONNECT THE POWER UNIT FROM THE
POWER SUPPLY. When using Hydraulic Foot
Pump 1583659 -1 or Hydraulic Hand Tool
1583661 -1, depress the pressure release pedal
to release pressure.
NOTE
i
The crimping head is designed and recommended for
use with the Foot Hydraulic Pump 1583659--1, Hand
Hydraulic Pump 1583661--1, or Electric Hydraulic
Pump 1804700--1 (115 Vac) or 1804700--2 (220 Vac).
3.2. Die Set
A. Installation
DANGER
Read these instructions and all applicable references
before inserting any die set assemblies and crimping
any terminals or splices.
To avoid personal injury, DO NOT accidentally
depress the footswitch or handle control when
installing or removing dies.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION (Figure 1)
Operating the crimping head WITHOUT the dies
installed will damage the “C” -head or ram.
CAUTION
The main components of the crimping head include a
“C”--head which houses the stationary die, a cylinder
which contains the crimping head hydraulic chamber,
!
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
1 of 3
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other products names, logos, or company names might be trademarks of their respective owners.
5秒后页面跳转
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
一文带你解读74HC244资料手册：特性、应用场景、封装方式、引脚配置说明、电气参数、推荐替代型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
