ICS181-01
LOW EMI CLOCK GENERATOR
External Components
The ICS181-01 requires a minimum number of external
components for proper operation.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
Decoupling Capacitor
A decoupling capacitor of 0.01µF must be connected
between VDD and GND on pins 6 and 3, as close to
these pins as possible. For optimum device
performance, the decoupling capacitor should be
mounted on the component side of the PCB. Avoid the
use of vias in the decoupling circuit.
1) The 0.01µF decoupling capacitor should be mounted
on the component side of the board as close to the
VDD pin as possible. No vias should be used between
the decoupling capacitor and VDD pin. The PCB trace
to VDD pin should be kept as short as possible, as
should the PCB trace to the ground via.
Series Termination Resistor
2) To minimize EMI, the 33Ω series termination resistor
(if needed) should be placed close to the clock output.
When the PCB trace between the clock output and the
load is over 1 inch, series termination should be used.
To series terminate a 50Ω trace (a commonly used
trace impedance) place a 33Ω resistor in series with
the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20Ω.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed
away from the ICS181-01. This includes signal traces
just underneath the device, or on layers adjacent to the
ground plane layer used by the device.
value of these capacitors is given by the following
equation:
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS181-01. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Item
Rating
Supply Voltage, VDD
All Inputs and Outputs
7 V
-0.5 V to VDD+0.5 V
0 to +70°C
-40 to +85°C
-65 to +150°C
125°C
Ambient Operating Temperature (commercial)
Ambient Operating Temperature (industrial)
Storage Temperature
Junction Temperature
Soldering Temperature
260°C
Recommended Operation Conditions
Parameter
Min.
Typ.
Max.
+85
Units
°C
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
-40
+3.135
+5.5
V
MDS 181-01 B
3
Revision 050405
Integrated Circuit Systemsl 525 Race Street, San Jose, CA 95126 l tel (408) 297-1201l www.icst.com
5秒后页面跳转
电子元器件中的网络滤波器、EMI滤波器与EMC滤波器：分类关系与功能详解
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
