Capacitor Hardware
Type VR Vertical Mounting Clamp
Catalog Part Number
Unassembled
Dimensions
Assembled
Diameter
of Part to be
Mounted
Without
Screw & Nut
with
Screw & Nut
VR1A
VR3A
VR4A
VR6A
VR8A
VR10A
VR12A
—
A
B
C
Screw & Nut
VR1B
Included
VR1
VR3
VR4
VR6
VR8
VR10
VR12
—
1" to 1-1/16
1-3/8" to 1-7/16
1-1/2" to 1-9/16
1-3/4" to 1-13/16
2" to 2-1/16
2-1/2" to 2-9/16
3" to 3-1/8
Screw
1"
1-7/16"
1-7/8*"
VR3B
1-3/8" 1-25/32" 2-7/32"
1-1/2" 1-15/16" 2-11/32"
VR4B
VR6B
1-3/4" 2-1/4"
2" 2-1/2"
2-1/2" 3"
3" 3-7/16"
2-9/16"
2-13/16"
3-5/16"
3-13/16"
VR8B
VR10B
VR12B
VRSCREW
VRNUT
9/16" long 6-32 thread NC-2A
Nut
—
—
Standard hex nut to fit screws
CDE VR mounting clamps may
VR1, 3 & 4
VR6, 8,10 & 12
be used to mount any cylindrical
capacitor with a 1” to 3” diameter
that is to be mounted in a vertical
position. Material is 1010 CRS,
commercial grade #4 temper
ASI scale. Parts are finished with
.0001 (nominal) zinc chromate
plating. Use for mounting CG
types, PSU, SF and MPF types.
Material thickness is .035”
B Mtng ±0.03”
.219”
C ±0.01”
0.176” x 0.281”
±0.016 (3 places).
.375”
.156”
B Mtg
120 º ±3 º
(3 Places)
75 º
A ±0.016”
2 Holes
.1561” Dia.
B Mtng ±0.03”
.562”
Ø 0.201” ±0.005”
.750”
0.375”±0.016”
0.075” ±0.016”
1.125” ±0.016”
0.035”
0.500” ±0.016”
Type TH Horizontal Mounting Clip
These clips, though designed
for capacitors, have varied ap-
plications to retain many cylin-
drical components. They are
used extensively in the electrical
and electronic industries to hold
spindles, condensers, capaci-
tors, tubes, rods and conduit.
Clips have phosphate and oil
finish.
Dimensions in Inches
Nominal Dia.
of Part to be
.*340” except TH25 is .590”
Catalog
Part Number
TH13
Mounted
.375
.625
A
B
.47
.250
.312
.312
.312
.312
TH17
TH21
.72
B
.875
1.000
1.375
1.00
1.06
1.50
TH23
TH25
A
.135” Dia
Hole
.594”
Material thickness TH13 thru
TH17 is .016”. TH21 thru TH25
is .020”
ACR15KT Motor Start Resistor Kit
ACR220KT Motor Run Resistor Kit
15K Ohm 2 watt bleeder resistors for AC motor start applica- 220K Ohm 1 watt bleeder resistors forAC motor run applica-
tions. Saves relay switch contacts and capacitor, particularly tions. Saves relay switch contacts and capacitor, particularly
in capacitor start applications. 1/4” quick connect terminals in capacitor run applications. 1/4” quick connect terminals
eliminate need for soldering.
eliminate need for soldering.
ACR15K:
ACR220K:
Pack of 10, 15K Ohm 2 watt bleeder resistor without quick Pack of 10, 220K Ohm 1 watt bleeder resistor without quick
connect terminals. connect terminals.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com