Functional Description
The 11C90 contains four ECL Flip-Flops, an ECL to TTL
converter and a Schottky TTL output buffer with an active
pull-up. Three of the Flip-Flops operate as a synchronous
shift counter driving the fourth Flip-Flop operating as an
asynchronous toggle. The internal feedback logic is such
that the TTL output and the Q ECL output are HIGH for six
clock periods and LOW for five clock periods. The Mode
Control (M) inputs can modify the feedback to make the
output HIGH for five clock periods and LOW for five clock
periods, as indicated in the Count Sequence Table.
TL/F/9892–10
The feedback logic is such that the instant the output goes
HIGH, the circuit is already committed as to whether the
output period will be 10 or 11 clock periods long. This
means that subsequent changes in an M input signal, in-
cluding decoding spikes, will have no effect on the current
output period. The only timing restriction for an M input sig-
nal is that it be in the desired state at least a setup time
before the clock that follows the HHLL state shown in the
table. The allowable propagation delay through external log-
ic to an M input is maximized by designing it to use the
positive transition of the 11C90 output as its active edge.
This gives an allowable delay of ten clock periods, minus
the CP to Q delay of the 11C90 and the M to CP setup time.
If the external logic uses the negative output transition as its
active edge, the allowable delay is reduced to five clock
periods minus the previously mentioned delay and setup
time.
FIGURE 3. Capacitively Coupled Clocking
TL/F/9892–11
Z
X
50
75
100
162
261
O
R X
80.6
130
121
196
1
R X
2
Capacitively coupled triggering is simplified by the 400X re-
sistor which connects pin 15 to the internal V reference.
BB
e
b
e
e b
2.0V
TT
V
5.2V, V
0V, V
EE
CC
By connecting this to the CP input, as shown inFigure 3, the
clock is automatically centered about the input threshold. A
clock duty cycle of 50% provides the fastest operation,
since the Flip-Flops are Master-Slave types with offset clock
thresholds between master and slave. This feature ensures
that the circuit will operate with clock waveforms having
very slow rise and fall times, and thus, there is no maximum
frequency restriction. Recommended minimum and maxi-
mum clock amplitude as a function of a frequency and tem-
perature are shown in the graph labeled Figure 2. When the
CP or any other input is driven from another ECL circuit,
normal ECL termination methods are recommended. One
method is indicated in Figure 4. Other ECL termination
methods are discussed in the F100K ECL Design Guide
(Section 5 of Databook).
FIGURE 4. Clocking by ECL Source via Terminated Line
When an M input is to be driven from a TTL output operating
and ground (V ), the internal 2 kX
EE
from the same V
CC
resistor can be used to pull the TTL output up as shown in
Figure 5. Some types of TTL outputs will only pull up to
within two diode drops of V , which is not high enough for
CC
11C90 inputs. The resistor will pull the signal up through the
threshold region, although this final rise may be somewhat
slow, depending on wiring capacitance. A resistor network
that gives faster rise and also lower impedance is shown in
Figure 6.
TL/F/9892–12
FIGURE 5. Using Internal Pull-Up with TTL Source
TL/F/9892–13
TL/F/9892–5
FIGURE 6. Faster Low Impedance TTL to ECL Interface
FIGURE 2. AC Coupled Triggering Characteristics
6
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
