Datasheet > 11AA160T-I/CS16K

11AA160T-I/CS16K

更新时间： 2024-01-01 19:44:45

品牌	Logo	应用领域
美国微芯 - MICROCHIP		可编程只读存储器电动程控只读存储器电可擦编程只读存储器内存集成电路
页数	文件大小	规格书
48页	747K
描述
2K X 8 1-WIRE SERIAL EEPROM, PBGA4, ROHS COMPLIANT, CSP-4

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

11AA160T-I/CS16K 技术参数

是否Rohs认证：	符合	生命周期：	Active
零件包装代码：	BGA	包装说明：	VFBGA, BGA4,2X2,35/16
针数：	4	Reach Compliance Code：	compliant
ECCN代码：	EAR99	HTS代码：	8542.32.00.51
Factory Lead Time：	8 weeks	风险等级：	1.77
数据保留时间-最小值：	200	耐久性：	1000000 Write/Erase Cycles
JESD-30 代码：	R-PBGA-B4	JESD-609代码：	e1
内存密度：	16384 bit	内存集成电路类型：	EEPROM
内存宽度：	8	功能数量：	1
端子数量：	4	字数：	2048 words
字数代码：	2000	工作模式：	SYNCHRONOUS
最高工作温度：	85 °C	最低工作温度：	-40 °C
组织：	2KX8	封装主体材料：	PLASTIC/EPOXY
封装代码：	VFBGA	封装等效代码：	BGA4,2X2,35/16
封装形状：	RECTANGULAR	封装形式：	GRID ARRAY, VERY THIN PROFILE, FINE PITCH
并行/串行：	SERIAL	峰值回流温度（摄氏度）：	NOT SPECIFIED
电源：	2/5 V	认证状态：	Not Qualified
座面最大高度：	0.55 mm	串行总线类型：	1-WIRE
最大待机电流：	0.000005 A	子类别：	EEPROMs
最大压摆率：	0.005 mA	最大供电电压 (Vsup)：	5.5 V
最小供电电压 (Vsup)：	1.8 V	标称供电电压 (Vsup)：	5 V
表面贴装：	YES	技术：	CMOS
温度等级：	INDUSTRIAL	端子面层：	TIN SILVER COPPER
端子形式：	BALL	端子节距：	0.4 mm
端子位置：	BOTTOM	处于峰值回流温度下的最长时间：	NOT SPECIFIED
最长写入周期时间 (tWC)：	10 ms	写保护：	SOFTWARE
Base Number Matches：	1

11AA160T-I/CS16K 数据手册

浏览型号11AA160T-I/CS16K的Datasheet PDF文件第10页

浏览型号11AA160T-I/CS16K的Datasheet PDF文件第11页

11XX

FIGURE 3-4:

MAK (‘1’)

ACKNOWLEDGE BITS

3.3

Acknowledge

SAK (‘1’)

An Acknowledge routine occurs after each byte is

transmitted, including the start header. This routine

consists of two bits. The first bit is transmitted by the

master, and the second bit is transmitted by the slave.

Note: A MAK must always be transmitted

NoMAK (‘0’)

NoSAK⁽¹⁾

following the start header.

The Master Acknowledge, or MAK, is signified by trans-

mitting a ‘1’, and informs the slave that the current

operation is to be continued. Conversely, a Not

Acknowledge, or NoMAK, is signified by transmitting a

‘0’, and is used to end the current operation (and initiate

the write cycle for write operations).

Note 1: A NoSAK is defined as any sequence that is not a

valid SAK.

3.4

Device Addressing

Note: When a NoMAK is used to end a

WRITE or WRSR instruction, the write

A device address byte is the first byte received from the

master device following the start header. The device

address byte consists of a four-bit family code, for the

11XX this is set as ‘1010’. The last four bits of the

device address byte are the device code, which is

hardwired to ‘0000’ on the 11XXXX0 devices.

cycle is not initiated if no bytes of data

have been received.

The slave Acknowledge, or SAK, is also signified by

transmitting a ‘1’, and confirms proper communication.

However, unlike the NoMAK, the NoSAK is signified by

the lack of a middle edge during the bit period.

The device code on 11XXXX1 devices is hardwired to

‘0001’. This allows both 11XXXX0 and 11XXXX1

devices to be used on the same bus without address

conflicts.

Note: In order to guard against bus conten-

tion, a NoSAK will occur after the start

header.

FIGURE 3-5:

DEVICE ADDRESS BYTE

ALLOCATION

A NoSAK will occur for the following events:

• Following the start header

• Following the device address, if no slave on the

bus matches the transmitted address

MAKSAK

SLAVE ADDRESS

• Following the command byte, if the command is

invalid, including Read, CRRD, Write, WRSR,

SETAL, and ERAL during a write cycle.

0⁽¹⁾

• If the slave becomes out of sync with the master

• If a command is terminated prematurely by using

a NoMAK, with the exception of immediately after

the device address.

Note 1: This bit is a ‘1’ on the 11XXXX1.

3.5

Bus Conflict Protection

See Figure 3.3 and Figure 3-4 for details.

To help guard against high current conditions arising

from bus conflicts, the 11XX features a current-limited

output driver. The IOL and IOH specifications describe

the maximum current that can be sunk or sourced,

respectively, by the SCIO pin. The 11XX will vary the

output driver impedance to ensure that the maximum

current level is not exceeded.

If a NoSAK is received from the slave after any byte

(except the start header), an error has occurred. The

master should then perform a standby pulse and begin

the desired command again.

FIGURE 3-3:

Master

ACKNOWLEDGE

ROUTINE

Slave

SAK

MAK

DS22067J-page 8

 2011 Microchip Technology Inc.

1...5 6 789 10 11...48

下载PDF

与11AA160T-I/CS16K相关器件

型号	品牌	描述	获取价格	数据表
11AA160T-I/MN	MICROCHIP	2K X 8 1-WIRE SERIAL EEPROM, PDSO8, 2 X 3 MM, 0.75 MM HEIGHT, ROHS COMPLIANT, PLASTIC, TDF	获取价格
11AA160T-I/MNY	MICROCHIP	1K-16K UNI/O® Serial EEPROM Family Data Sheet	获取价格
11AA160T-I/MS	MICROCHIP	1K-16K UNI/O® Serial EEPROM Family Data Sheet	获取价格
11AA160T-I/P	MICROCHIP	1K-16K UNI/O® Serial EEPROM Family Data Sheet	获取价格
11AA160T-I/SN	MICROCHIP	1K-16K UNI/O® Serial EEPROM Family Data Sheet	获取价格
11AA160T-I/TO	MICROCHIP	2K X 8 1-WIRE SERIAL EEPROM, PBCY3, ROHS COMPLIANT, PLASTIC, TO-92, 3 PIN	获取价格

产品中心

服务支持

精选活动

关于我们

帮助中心

11AA160T-I/CS16K

11AA160T-I/CS16K 技术参数

11AA160T-I/CS16K 数据手册

与11AA160T-I/CS16K相关器件

与11AA160T-I/CS16K相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

11AA160T-I/CS16K

11AA160T-I/CS16K 技术参数

11AA160T-I/CS16K 数据手册

与11AA160T-I/CS16K相关器件

与11AA160T-I/CS16K相关文章

您还可以找

您在本页遇到什么问题？