Datasheet > 10209S2-525N

10209S2-525N

更新时间： 2022-12-16 23:43:52

品牌	Logo	应用领域
RFSOLUTIONS		远程控制
页数	文件大小	规格书
5页	71K
描述
KEELOQ REMOTE CONTROL SYSTEMS, 230Vac

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

10209S2-525N 数据手册

119, 129

10209

KEELOQ REMOTE CONTROL SYSTEMS, 230Vac

Data Outputs

Each of the transmitter switches maps directly to the relay outputs. (SW1 to RLY1, SW2 to RLY2)

Each output relay provides an isolated switch. Connections are Common (COM), Normally Open (NO) and

Normally Closed (NC).

Relay Connections when

Transmitter NOT Operating

Relay Connections when

Transmitter OPERATING

The jumper links ( LK1, LK2 ) configure the outputs to be momentary or latching.

LK1

Open

LK2

Open

Connected

Open

O/P 1

Mom

Latch

O/P2

Mom

Latch

Mom

Latch

Connected

Note : In momentary mode the relay will operate for as long as the transmitter switch is held on.

Learning a new Transmitter Encoder

To enter and activate the learn mode the following sequence must be performed.

1. Power the receiver unit up and wait 10secs for the unit to enter ‘normal operation’ mode.

2. Switch the receiver unit OFF and then ON again in ~1sec intervals four times finally leaving the unit

powered up.

3. After 5secs until a ‘beep’ sound is heard.

4. The unit is now in ‘learn’ Mode.

5. Briefly press a button on the transmitter, the receiver unit will ‘beep’ twice.

6. Briefly Press the transmitter button again, he receiver unit will ‘beep’ three times.

7. Wait 10sec for the unit to return to ‘normal operation’ mode.

8. The transmitter is now ‘learnt’ to the receiver unit and will operate the output relays.

Erasing Transmitter Encoders form Memory

To enter and activate the erase mode the following sequence must be performed.

1. Power the receiver unit up and wait 10secs for the unit to enter ‘normal operation’ mode.

2. Switch the unit off and then on again in ~1sec intervals six times finally leaving the unit powered up.

3. Wait 5secs until a ‘ticking’ sound is heard for a period of 10secs by the operation and release of one of the

relays.

4. Wait 10secs for the receiver unit to return to ‘normal’ mode

5. The unit has now erased all encoder data.

Note

During Learn and Erase the relays should not be connected to equipment that will be harmed by rapid

changes of the relay polarisation.

DS119-5 June ‘06

Page 3

1 234 5

下载PDF

与10209S2-525N相关器件

型号	品牌	描述	获取价格	数据表
1020B5743-01	ETC	Flavus 2.4 GHz Snap-In Antenna	获取价格
1020B5743-02	ETC	Flavus 2.4 GHz Snap-In Antenna	获取价格
1020B5743-03	ETC	Flavus 2.4 GHz Snap-In Antenna	获取价格
1020B5743-04	ETC	Flavus 2.4 GHz Snap-In Antenna	获取价格
1020B5743-05	ETC	Flavus 2.4 GHz Snap-In Antenna	获取价格
1020B5786-01	ETC	Flavus 2.4 / 5 GHz Snap-In Antenna	获取价格