Absolute Maximum Ratings(Note 1)
Recommended Operating
Conditions
Storage Temperature (TSTG
Maximum Junction Temperature (TJ)
EE Pin Potential to Ground Pin
)
−65°C to +150°C
+150°C
Case Temperature (TC)
Commercial
V
−7.0V to +0.5V
VEE to +0.5V
−50 mA
0°C to +85°C
−40°C to +85°C
−5.7V to −4.2V
Input Voltage (DC)
Industrial
Output current (DC Output HIGH)
ESD (Note 2)
Supply Voltage (VEE
)
≥2000V
Note 1: The “Absolute Maximum Ratings” are those values beyond which
the safety of the device cannot be guaranteed. The device should not be
operated at these limits. The parametric values defined in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recommended Operating Conditions” table will define the conditions
for actual device operation.
Note 2: ESD testing conforms to MIL-STD-883, Method 3015.
Commercial Version
DC Electrical Characteristics (Note 3)
VEE = −4.2V to −5.7V, VCC = VCCA = GND, TC = 0°C to +85°C
Symbol
Parameter
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Min
Typ
−955
−1705
Max
−870
Units
mV
Conditions
Loading with
VOH
VOL
−1025
−1830
−1035
V
IN =VIH (Max)
or VIL (Min)
IN = VIH (Min)
−1620
mV
50Ω to −2.0V
Loading with
50Ω to −2.0V
VOHC
VOLC
VIH
mV
V
−1610
−870
mV
or VIL (Max)
−1165
−1830
0.50
mV
Guaranteed HIGH Signal
for All Inputs
VIL
Input LOW Voltage
−1475
mV
µA
µA
mA
Guaranteed LOW Signal
for All Inputs
IIL
Input LOW Current
Input HIGH Current
VIN = VIL (Min)
IIH
I0X–I3X
340
300
−39
VIN = VIH (Max)
S0, S1, E
IEE
Power Supply Current
−75
Inputs Open
Note 3: The specified limits represent the “worst case” value for the parameter. Since these values normally occur at the temperature extremes, additional
noise immunity and guardbanding can be achieved by decreasing the allowable system operating ranges. Conditions for testing shown in the tables are cho-
sen to guarantee operation under “worst case” conditions.
DIP AC Electrical Characteristics
V
EE = −4.2V to −5.7V, VCC = VCCA = GND
Symbol Parameter
Propagation Delay
T
C = 0°C
T
C = +25°C
TC = +85°C
Units
ns
Conditions
Min
Max
Min
Max
Min
Max
tPLH
tPHL
tPLH
tPHL
tPLH
tPHL
tTLH
tTHL
0.45
0.90
0.65
0.35
1.50
2.40
2.30
1.20
0.45
1.50
0.45
1.60
I0x–I3x to Output
Propagation Delay
S0, S1 to Output
Propagation Delay
E to Output
Figures 1, 2
(Note 4)
0.90
0.65
0.35
2.40
2.30
1.20
1.00
0.75
0.35
2.60
2.40
1.20
ns
ns
Transition Time
ns
Figures 1, 2
20% to 80%, 80% to 20%
Note 4: The propagation delay specified is for single output switching. Delays may vary up to 300 ps with multiple outputs switching.
3
www.fairchildsemi.com