Datasheet > 02-08-1235

02-08-1235

更新时间： 2022-03-30 03:23:41

品牌	Logo	应用领域
莫仕 - MOLEX		/
页数	文件大小	规格书
6页	322K
描述
HAND CRIMP TOOL SPECIFICATION SHEET

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

02-08-1235 数据手册

Hand Tool for Disk Drive Power Connection System Crimp Terminals

LUBRICATION POINTS

(BOTH SIDES) LIGHT OIL

(EVERY 3 MONTHS OR

5,000 CRIMPS)

Maintenance

It is recommended that each operator of the tool be made aware

of, and responsible for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean

brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the

tool.

3. Make certain all pins; pivot points and bearing surfaces are

protected with a thin coat of high quality machine oil. Do not

oil excessively. The tool was engineered for durability but

like any fine piece of equipment it needs cleaning and

Figure 5

lubrication for a maximum service life of trouble free crimping. Light oil such as 30 weight automotive oil used

at the oil points, every 5,000 crimps or 3 months, shown in Figure 6 will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

PRELOAD

CHECK POINT

25.4MM

Should this tool ever become stuck or jammed in a

partially closed position, Do Not force the handles

open or closed. The tool will open easily by

pressing the ratchet release lever. See Figure 6.

SETTING WHEEL

ECCENTRIC AXLE

How to Adjust Tool Preload

(See Figure 6)

RATCHET

RELEASE LEVER

HANDLE

GRIP

REMOVED

This hand tool is factory preset to 25-45 LBS.

preload. It may be necessary over the life of the

tool to adjust tool handle preload force. Listed

below are the steps required to adjust the crimping

force of the hand tool to obtain proper crimp

conditions:

WRENCH SET

(SOLD

SEPERATELY)

Figure 6

LOCKING

SCREW

HANDLE

GRIP

1. Remove or fold back the handle grip from the handle to expose the eccentric axle and setting wheel.

2. Remove the locking screw with a 2mm hex wrench. The wrench set (63810-0101), is not supplied. It is sold

separately from the hand tool.

3. Turn the eccentric axle and setting wheel with the wrench or pliers Counter-clockwise (CCW) to increase handle

force.

4. Replace the locking screw, aligning the nearest notch in the setting wheel to locking screw.

5. Replace the handle grip.

6. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.

Doc No: ATS-638117000

Revision: B

Release Date: 01-19-07

Revision Date: 03-29-08

UNCONTROLLED COPY

Page 4 of 6

1 2 345 6

下载PDF

与02-08-1235相关器件

型号	品牌	描述	获取价格	数据表
02-08-1236	MOLEX	HAND CRIMP TOOL SPECIFICATION SHEET	获取价格
02-08-1237	MOLEX	HAND CRIMP TOOL SPECIFICATION SHEET	获取价格
020813236100000	KYOCERA AVX	Board Stacking Connector, 81 Contact(s), 1 Row(s), Male, Straight, Solder Terminal,	获取价格
020813276100000	KYOCERA AVX	Board Stacking Connector, 81 Contact(s), 1 Row(s), Male, Straight, Solder Terminal,	获取价格
02-08-1334	MOLEX	HAND CRIMP TOOL SPECIFICATION SHEET	获取价格
02-08-1335	MOLEX	HAND CRIMP TOOL SPECIFICATION SHEET	获取价格