0.75T8A_1.5RP series
0.75W - Single Output DC-DC Converter - Fixed Input - Isolated & Regulated
DC-DC Converter
0.75 Watt
The 0.75T8A_1.5RP series is specially designed for applications where a group of
polar power supplies are isolated from the input power supply in a distributed
power supply system on a circuit board.
Small footprint
Low temperature rise
Internal SMD construction
Meets UL62368, EN62368
standards
Compact SMD package
High efficiency up to 74%
1500VDC isolation
These products apply to:
Temperature range:
-40°C ~ +85°C
Industry standard pinout
RoHS compliance
1) Where the voltage of the input power supply is fixed (voltage variation ≤ 10ꢀ)
2) Where isolation is necessary between input and output
(isolation voltage ≤1500VDC)
Short circuit protection (SCP)
3) Where the regulation of the output voltage and the output ripple noise are
not demanding
Such as: digit circuit condition; normal low-frequency artificial circuit condition;
relay drive circuit condition, etc.
UL-62368-1 (E347551)
Common specifications
Short circuit protection:
Temperature rise at full load:
Output specifications
Continuous, automatic recovery
Item
Test condition
Min
Typ
Max
3
Units
ꢀ
25°C TYP (Ta= 25°C)
3.3VDC output: 30°C
Output voltage
accuracy
Cooling:
Free air convection
-40°C~+85°C
Line regulation
Load regulation
For Vin change of 1ꢀ
0.25
ꢀ
Operation temperature range:
Storage temperature range:
Lead temperature
10ꢀ to 100ꢀ load
• 3.3V output
• other output
3
2
ꢀ
ꢀ
-55°C ~+125°C
300°C MAX, 1.5mm from case for 10 sec
Temperature drift
Ripple & Noise*
100ꢀ full load
0.03
75
ꢀ/°C
mVp-p
KHz
Reflow soldering temperature:
Peak temp.≤245°C, maximum duration
time ≤60s at 217°C.
20MHz Bandwidth
30
Switching frequency Full load, nominal input
270
Moisture Sensitivity Level (MSL)
Storage humidity range:
Package material:
IPC/JEDEC J-STD-020D.1, Level 2
< 95ꢀ
* Ripple and noise tested with “parallel cable” method. See detailed operation
instructions at DC-DC Application Notes.
Epoxy Resin [UL94-V0]
>3,500,000 hours
13.20*11.40*7.25mm
1.4g
MTBF (MIL-HDBK-217F@25°C):
Dimensions:
EMC specifications
EMI
EMI
EMS
CE
CISPR22/EN55032
CLASS B (External Circuit Refer to
EMC recommended circuit)
Weight:
RE
CISPR22/EN55032
CLASS B (External Circuit Refer to
EMC recommended circuit)
Input specifications
Item
Test condition
5VDC input
Min
Typ
Max
Units
ESD
IEC/EN61000-4-2
perf. Criteria B
Contact 6KV
Input current
(full load / no load) • 3.3/5VDC output
• 9/12VDC output
221/5
234/10 mA
208/12 221/20 mA
202/18 215/30 mA
• 15VDC output
Reflected ripple
current*
15
mA
Example:
0.75T8A_0505S1.5RP
0.75 = 0.75Watt; T8 = SMT8; A = Pinning; 5Vin; 5Vout; S = Single output;
1.5 = 1.5kVDC; R= Regulated output; P = Short circuit protection
Input filter
Hot plug
Filter capacitor
Unavailable
* Reflected ripple current testing method please see DC-DC Converter Application
Notes for specific operation.
Note:
1. Operation under minimum load will not damage the converter; However, they
may not meet all specification listed.
2. Max. Capacitive Load tested at input voltage range and full load.
3. All specifications measured at Ta = 25°C, humidity <75ꢀ, nominal input voltage
and rated output load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on our corpo-
rate standards.
Isolation specifications
Item
Test condition
Min
Typ
20
Max
Units
VDC
Isolation voltage
Tested for 1 minute and 1500
1mA max
Isolation resistance
Test at 500VDC
1000
MΩ
pF
Isolation
capacitance
Input/Output 100KHz/1V
Page 1 of 3
0.75T8A_1.5RP – Rev. 2020-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com