TDA9885; TDA9886
NXP Semiconductors
I2C-bus controlled multistandard alignment-free IF-PLL demodulators
Table 1.
Symbol
S/NW
Quick reference data …continued
Parameter Conditions
weighted signal-to-noise unified weighting filter (“ITU-T J.61”);
Min
Typ
Max
Unit
[5]
56
59
-
dB
ratio
see Figure 13
PSRRCVBS power supply ripple
rejection on pin CVBS
fripple = 70 Hz; video signal; grey level;
positive and negative modulation;
see Figure 8
20
25
-
dB
AFCstps
AFC control steepness
definition: ∆IAFC / ∆fVIF
0.85
430
1.05
540
1.25
650
µA/kHz
Audio part
Vo(AF)(rms) AF output voltage
(RMS value)
27 kHz FM deviation; 50 µs de-emphasis
mV
THD
total harmonic distortion
25 kHz FM deviation; 50 µs de-emphasis
-
0.15
0.5
0.50
1.0
-
%
54 % AM modulation
-
%
BAF(−3dB)
S/NW(AF)
−3 dB AF bandwidth
without de-emphasis; measured with
FM-PLL filter of Figure 26
80
100
kHz
weighted signal-to-noise black picture; see Figure 21
ratio of audio signal
50
45
40
56
50
46
-
-
-
dB
dB
dB
in accordance with “ITU-R BS.468-4”
αAM(sup)
AM suppression of
FM demodulator
referenced to 27 kHz FM deviation;
50 µs de-emphasis; AM: f = 1 kHz;
m = 54 %
PSRRAM
PSRRFM
power supply ripple
rejection
see Figure 8
20
14
26
20
-
-
dB
dB
power supply ripple
rejection
fripple = 70 Hz; see Figure 8
Vo(intc)(rms) IF intercarrier output level QSS mode; SC1; SC2 off
90
90
-
140
140
75
180
180
-
mV
mV
mV
(RMS value)
L standard; without modulation
[6]
[7]
intercarrier mode; PC / SC1 = 20 dB;
SC2 off
Reference frequency input; pin REF
fref
reference signal
frequency
-
4
-
-
MHz
mV
Vref(rms)
reference signal voltage
(RMS value)
operation as input terminal
80
400
[1] Values of video and sound parameters can be decreased at VP = 4.5 V.
[2] The sound carrier trap can be bypassed by switching the I2C-bus. In this way the full composite video spectrum appears at pin CVBS.
The amplitude is 1.1 V (p-p).
[3] Condition: luminance range (5 steps) from 0 % to 100 %.
[4] AC load; CL < 20 pF and RL > 1 kΩ. The sound carrier frequencies (depending on TV standard) are attenuated by the integrated sound
carrier traps (see Figure 15 to Figure 20; H (s) is the absolute value of transfer function).
[5] S/N is the ratio of black-to-white amplitude to the noise voltage (RMS value measured on pin CVBS and tested at video black level,
‘quiet line’). Noise analyzer settings: B = 5 MHz, 200 kHz high-pass and sound carrier trap on. In case of S/NW weighted in accordance
with “ITU-T J.61”. Measurements taken for B/G standard.
[6] The intercarrier output signal at pin SIOMAD can be calculated by the following formula taking into account the internal video signal with
Vi(SC)
1
1
1
1.1 V (p-p) as a reference: Vo(intc)(rms) = 1.1 ×
× 10r V and r =
×
(dB) + 6 dB ± 3 dB , where:
is the
---------
-----
20
---------------
---------
Vi(PC)
2 2
2 2
Vi(SC)
correction term for RMS value,
(dB) is the sound-to-picture carrier ratio at pins VIF1 and VIF2 in dB, 6 dB is the correction term
---------------
Vi(PC)
of internal circuitry and ±3 dB is the tolerance of video output and intercarrier output Vo(intc)(rms)
.
TDA9885_TDA9886_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 16 December 2008
3 of 56