Electrical Specifications
Part Number
VDRM
IT
& VRRM
IGT
IDRM & IRRM
VTM
VGT
IH
Non-Isolated
Maximum
On-State
Current
(1)
Repetitive
DC Gate
Peak Off-State
Peak
DC Gate-
DC Holding
Peak
Trigger
Forward & Reverse On-State
Trigger
Current
Off-State
Forward
& Reverse
Voltage
Current
Current at
VDRM & VRRM
(12)
Voltage at
Voltage
Gate Open
(4) (11)
V
D = 12VDC
Max Rated VD = 12VDC
R
L = 60Ω
RMS
Current
C = 25°C
(2)
R
L = 60Ω
TYPE
(3)
(7)
T
D2Pak
Amps
mAmps
Volts
TC
=
TC
=
TC
=
TC
=
TC =
IT(RMS) IT(AV)
Volts
MIN
100
200
400
600
800
100
200
400
600
800
100
200
400
600
800
100
200
400
600
800
mAmps
25°C 100°C 125°C
MAX
Volts
MAX
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
25°C 125°C
mAmps
MAX
40
40
40
40
40
50
50
50
50
50
60
60
60
60
60
MAX
16
16
16
16
16
25
25
25
25
25
40
40
40
40
40
55
55
55
55
55
MAX
10
10
10
10
10
16
16
16
16
16
25
25
25
25
25
35
35
35
35
35
MIN
MAX
30
30
30
30
30
35
35
35
35
35
40
40
40
40
40
40
40
40
40
40
MAX
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
MIN
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
S1016N
S2016N
S4016N
S6016N
**S8016N
S1025N
S2025N
S4025N
S6025N
**S8025N
S1040N
S2040N
S4040N
S6040N
**S8040N
S1055N
S2055N
S4055N
S6055N
**S8055N
1
1
1
1
1
1
1
1
.01
.01
.01
.01
.02
.01
.01
.01
.01
.02
.01
.01
.01
.01
.02
.01
.01
.01
.01
.02
0.5
0.5
0.5
0.5
1.0
1.0
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.0
1.5
1.0
1.0
1.0
1.0
2.0
2.0
2.0
2.0
2.0
3.0
2.0
2.0
2.0
2.0
3.0
2.0
2.0
2.0
2.0
3.0
16 A
25 A
40 A
55 A
1
1
5
5
5
5
5
5
60
60
60
60
5
5
5
5
60
** Cunsult factory for 1000 volt device
Electrical Specification Notes
(1) See Figures 1.2 through 1.9 for current rating at specified operat-
General Notes
ing case temperature.
•
All measurements are made at 60Hz with a resistive load at an
ambient temperature of +25°C unless otherwise specified.
(2) See Figures 1.12 and 1.13 for instantaneous on-state current vs
on-state voltage (typical).
(3) See Figure 1.11 for I vs T .
GT
C
•
•
•
Operating temperature range (T ) is -40°C to +125°C
J
(4) See Figure 1.10 for I vs T .
H
C
Storage temperature range (T ) is -40°C to +150°C
S
(5) For more than one full cycle rating, see Figure 1.18.
Lead solder temperature is a maximum of 230°C for 10 seconds
maximum; 1/16" (1.59mm) from case.
(6) See Figure 1.15 for t vs I
.
GT
C
gt
(7) See Figure 1.14 for V vs T .
GT
(8) Test conditions are as follows: 2A .Pulse duration = 50µs,
•
The case temperature (T ) is measured as shown on dimensional
C
dv/dt = 20V/µs, di/dt = -30A/µs I = 200mA at turn-on.
outline drawings. See “Package Dimensions” section of this
catalog.
GT
(9) See Figures 1.2 through 1.5 for maximum allowable case temper-
atures at maximum rated current.
(10) Pulse width ≤ 10µs.
(11) Initial on-state current = 200mA(DC) for 16A devices; 400mA(DC)
for 25A through 55A devices.
(12) T = T for test conditions in off-state.
C
J
D2Pak SCR
2
2001 Teccor Electronics
+1 972 580-7777