®
RT5016C
I2C Programmable Multi-Channel PMU with Battery Charger
for CMOS DSC/DV
General Description
Charging tasks are optimized by using a control algorithm
to vary the charge rate, including pre-charge mode, fast
charge mode and constant voltage mode. The charge
current can also be programmed via the I2C control
interface. The battery regulation voltage and current can
be adjusted by JEITAstandard temperature control or other
schemes set via the I2C interface. The internal thermal
feedback circuitry regulates the die temperature to optimize
the charge rate for all ambient temperatures. The charging
task will always be terminated in constant-voltage mode
when the charging current reduces to the termination
current of 10% x ICHG_FAST. The charger includes under-
voltage and over-voltage protection for the supply input
voltage, VIN. The charger includes USB charger detection
circuitry via D+ and D- pins of USB interface to detect
USB standard downstream ports (SDP), dedicated charger
port (DCP), orApple/Sony charger ports. RT5016C uses
some indicators to show charger states : two open drain
ports CHGand CHG2, and an interrupt (INT) to immediately
notify the state change.
The RT5016C is a complete power supply solution for
digital still cameras and other hand held devices. The
RT5016C is composed of a multi-channelDC-DC power
converter unit, a single-cell linear Li-ion battery charger, a
charger type detector, and an I2C control interface.
The power converter unit includes one synchronous step-
up converter (CH1), one synchronous step-up/down
converter (CH2), three synchronous step-down converters
(CH3/4/5), two LDOs with input power as low as 1.5V
(CH6/8), one WLED driver in synchronous high-voltage
step-up mode or low-voltage current regulator mode (CH7),
and a keep-alive LDO (CH9) for RTC application. All
converters are internally frequency compensated and
integrate power MOSFETs. The power converter unit
provides complete protection functions : over-current,
thermal shutdown, over-voltage, and under-voltage
protection. The RT5016C has a WAKEUP impulse
generation circuitry to monitor VIN or BAT installation
event. To fulfill most of applications, the RT5016C has six
preset power-on/off sequences.
The RT5016C has I2C interface to control rich functions of
Power Converter Unit and Charger Unit, and is available in
the WQFN-40L 5x5 package.
The battery charger includes Auto Power Path
Management (APPM).No external MOSFETs are required.
The charger can enter sleep mode when power is removed.
Simplified Application Circuit
BAT
Charger for Battery
PVD1
VO2
LX3
Adapter/USB
VIN
Step-Up for Motor
Step-Up/Down for I/O
Step-Down for Core
Step-Down for Memory
Step-Down
RT5016C
SYS
System Power
LX4
SCL
SDA
2
LX5
I C Control
VO6
PVD7
VO8
VRTC
LDO
Step-Up for LED Backlight
LDO
GND
LDO for RTC
Copyright 2016 Richtek Technology Corporation. All rights reserved.
©
is a registered trademark of Richtek Technology Corporation.
DS5016C-02 November 2016
www.richtek.com
1
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
