Datasheet > R0603-DNP

R0603-DNP

更新时间： 2022-05-06 21:41:10

品牌	Logo	应用领域
德州仪器 - TI		放大器功率放大器
页数	文件大小	规格书
12页	343K
描述
TPA2025D1 Audio Power Amplifier Evaluation Module

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

R0603-DNP 数据手册

Operation

www.ti.com

1.2 TPA2025D1 Specifications

V_BAT

I_DD

P_O

V_I

Supply voltage range

2.5 V to 5.2 V

Supply current

3 A Maximum

2 W

Continuous output power per channel, 4 Ω, V_BAT= 3.6 V

Audio input voltage

0 V to V_BAT

4 Ω

R_L

Minimum load impedance

Operation

This section describes how to operate the TPA2025D1EVM.

2.1 Quick-Start List for Stand-Alone Operation

Use the following steps when operating the TPA2025D1EVM as a stand-alone or when connecting the

EVM into existing circuits or equipment.

2.1.1

2.1.2

Power and Ground

1. Ensure the external power sources are set to OFF.

2. Set the power supply voltage between 2.3 V and 5.2 V. When connecting the power supply to the

EVM, attach the power supply ground connection to the GND connector first, and then connect the

positive supply to the VDD connector. Verify that correct connections are made to the banana jacks.

Audio

1. Ensure that the audio source is set to the minimum level.

2. Connect the audio source to the input RCA jack IN. In case of differential audio input, ensure that the

jumper, JP SE, is not inserted. In case of a single-ended audio input, ensure that the jumper, JP SE, is

inserted, thereby grounding IN+ through the input capacitor C2.

3. Connect a speaker (4 Ω to 32 Ω) to the output banana jacks, OUT+ and OUT–.

4. FLT Out+ and FLT OUT- test points allow the user to connect the outputs of the amplfier through an

RC filter for audio measurements. (Many audio analyzers will not give the correct readings on a

Class-D amplifier without additional filtering.) Note that the user must provide the necessary resistors,

R7 and R8 to complete the filters. The typical value for R7 and R8 is 1.0 kΩ.

5. The filtered output of the TPA2025D1 can be measured between test points FILT OUT– and FILT

OUT+

2.1.3

AGC Control

The TPA2025D1 has three selectable inflection point settings: 3.25 V, 3.55 V, and 3.75 V.

1. Remove the jumper, AGC, to select the 3.25-V inflection point (AGC1).

2. Install the jumper, AGC, between pins 2 and 3 to select the 3.55-V inflection point (AGC2).

3. Install the jumper, AGC, between pins 1 and 2 to select the 3.75-V inflection point (AGC3).

2.1.4

2.1.5

Amplifier Gain

The TPA2025D1 has a fixed setting of 20 dB.

Shutdown Controls

1. The TPA2025D1 provides shutdown control for the Class-D amplifier and the boost converter. The EN

pin enables the boost converter and Class-D amplifier. It is active high.

2. Press and hold pushbutton S1 to place the boost converter and the Class-D amplifier in shutdown.

Release pushbutton S1 to activate the Class-D amplifier and boost converter. The boost converter only

turns on if an audio signal (> 2 V_PEAK) is present at one of the outputs (OUT+ or OUT-).

TPA2025D1 Audio Power Amplifier Evaluation Module

SLOU310–September 2011

Submit Documentation Feedback

123 4 5 6 7...12

下载PDF

与R0603-DNP相关器件

型号	品牌	描述	获取价格	数据表
R0605250L	ETC	Si Reverse Hybrid , low current	获取价格
R0605250L1	PDI	Si Reverse, low current, 5 - 65 MHz, 25.2dB typ. Gain @ 65MHz, 135mA max. @ 24VDC	获取价格
R0605250L2	PDI	Si Reverse, low current, 5 - 65 MHz, 25.0dB typ. Gain @ 65MHz, 140mA max. @ 24VDC	获取价格
R0605280L2	PDI	Si Reverse, low current, 5 - 65 MHz, 28.0dB typ. Gain @ 65MHz, 140mA max. @ 24VDC	获取价格
R0605300L	PDI	Si Reverse, low current, 5 - 65MHz, 30.5dB typ. Gain @ 65MHz, 135mA max. @ 24VDC	获取价格
R0605300L1	PDI	Si Reverse, low current, 5 - 65MHz, 30.5dB typ. Gain @ 65MHz, 135mA max. @ 24VDC	获取价格

与R0603-DNP相关文章

TLP250光耦合器：资料手册参数分析
2024-05-09

4
DA14580 低功耗蓝牙系统级芯片(SoC)：资料手册参数分析
2024-05-09

6
INA226 高精度电流和功率监控器：资料手册参数分析
2024-05-09

5
SI2302 N沟道MOSFET：资料手册参数分析
2024-05-09

8

产品中心

服务支持

精选活动

关于我们

帮助中心

R0603-DNP

R0603-DNP 数据手册

与R0603-DNP相关器件

与R0603-DNP相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

R0603-DNP

R0603-DNP 数据手册

与R0603-DNP相关器件

与R0603-DNP相关文章

您还可以找

您在本页遇到什么问题？