PSCPF100 SERIES
Up to 102.6 Watts
AC/DC Power Supply
Single Output
Rev A
SPECIFICATIONS
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.
We reserve the right to change specifications based on technological advances.
SPECIFICATION
PROTECTION
TEST CONDITIONS
Min
Typ
Max
Unit
Short Circuit Protection
Yes
135
Constant current limiting, recovers automatically after fault condition is
removed
% Rated
Output Power
Over Load Protection
105
Shut down o/p voltage, re-power on to recover
See Table for Ranges
Over Voltage Protection
Over Voltage Category III; According to EN61558, EN50178, EN60664-1,
EN62477-1, altitude up to 2000 meters
Over Temperature Protection
Shut down o/p voltage, recovers automatically after temperature goes down
ENVIRONMENTAL SPECIFICATIONS
Working Temperature
Storage Temperature
Working Humidity
Storage Humidity
Vibration
See Derating Curve
-30
-40
20
+70
+85
90
ºC
ºC
%RH
%RH
Non-Condensing
10
95
10~500Hz, 2G 10min/1cycle, 60min. each along X, Y, Z axes
MIL-HDBK-217F, 25ºC
MTBF
288.5
Khours
GENERAL SPECIFICATIONS
Efficiency
See Table
4KVAC
I/P-O/P
Withstand Voltage
I/P-FG
2KVAC
O/P-FG
0.5KVAC
Isolation Resistance
PHYSICAL SPECIFICATIONS
Weight
I/P-O/P, I/P-FG, O/P-FG
100MΩ/500VDC/25ºC/70%RH
18.34oz (520g)
7.05in x 3.90in x 1.18in
(179mm x 99mm x 30mm)
24pcs/14.5kg/0.84CUFT
Dimensions (L x W x H)
Packing
SAFETY CHARACTERISTICS
UL60950-1
TUV EN60950-1
EN61558-1
EN61558-2-16
Safety Approvals
EAC TP TC 004
CCC GB4943.1
EN55032 (CISPR32)
EN61000-3-2,-3
EAC TP TC 020
GB9254
Class B
EMC Emission
EMC Immunity
Class B
GB17625.1
EN61000-4-2, 3, 4, 5, 6, 8, 11
EN55024
Light Industry Level
Criteria A
EAC TP TC 020
NOTES
1. Ripple & Noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Tolerance includes set up tolerance, line regulation, and load regulation.
3. The power supply is considered a component which will be installed into final equipment. Final equipment must be re-confirmed that it still meets
EMC directives.
4. It is strongly recommended that external output capacitances should not exceed 5000uF (only for 3.3VDC, 5VDC, and 7.5VDC models)
5. Ambient temperature derating of 3.5ºC/1000m with fanless models and of 5ºC/1000m with fan models for operating altitude higher than 2000m
(6500ft).
6. This product is listed to applicable standards and requirements by UL.
*Due to advances in technology, specifications subject to change without notice.
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 •
11/29/2018
Fax 603-778-9797
Page 2 of 4
website: www.wallindustries.com • e-mail: sales@wallindustries.com