CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Standard
PLF
Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
PLG
Lead free flow soldering condition correspondence.
Higher
Compliant to the RoHS directive (2011/65/EU).
Capacitance
Long Life
Low ESR
PLS
PLE
PLF
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–55 to +105°C
2.5 to 25V
Rated Capacitance Range
Capacitance Tolerance
6.8 to 1500µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
Tangent of loss angle (tan δ)
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z–55°C / Z+20°C 1.25
(100kHz)
(
3
)
)
Capacitance change
Within 20% of the initial capacitance value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
(
3
Capacitance change
Within 20% of the initial capacitance value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
(
3
)
Capacitance change
Within 10% of the initial capacitance value
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 560 F)
µ
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
Voltage(g:4V)
P L F 0 G 5 6 1 M D O 1
Size code
Configuration
Capacitance tolerance ( 20ꢀ%
φd
Series
Lot. No.
Rated capacitance
(
560µF
%
%
+0.5MAX.
15MIN
4MIN
L
Rated voltage
(4V
Series name
Type
(mm)
Voltage
V
Size
φD
L
P
φd
φ6.3 × 6L φ6.3 × 9L φ6.3
×
10.5L φ8 × 7L φ8 × 9L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 13L
2.5
e
4
g
6.3 10 16 20 25
6.3
5.5
6.3
8.5
2.5
0.6
6.3
10.0
2.5
8.0
6.5
3.5
0.6
8.0
8.5
3.5
0.6
8.0
11.5
3.5
10.0
7.5
5.0
10.0
9.5
5.0
10.0
12.5
5.0
Code
j
A
C
D
E
2.5
0.45
Frequency coefficient of rated ripple current
0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more
0.5
0.6
0.6
0.6
0.6
Coefficient
0.05
0.30
0.70
1.00
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
56