Datasheet > N0416SC040

N0416SC040

更新时间： 2023-12-06 20:13:28

品牌	Logo	应用领域
力特 - LITTELFUSE		/
页数	文件大小	规格书
11页	894K
描述
Littelfuse提供业界最全面的标准相位控制晶闸管系列之一。器件电压范围在400V至6500V，适合用于线电压230V至1000V以上的应用（电压更高的应用现可使用我们的中压晶闸管系列）。

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

N0416SC040 数据手册

Fast Turn-Off Thyristor N0416SC040-N0416SC080

The total dissipation is now given by:

W =W_(original)+ E × f

(TOT)

11.2 Determination without Measurement

In circumstances where it is not possible to measure voltage and current conditions, or for design

purposes, the additional losses E in joules may be estimated as follows.

Let E be the value of energy per reverse cycle in joules (curves in Figure 9).

Let f be the operating frequency in Hz

T_SINK

= T_SINK

)

(

E × R_th× f

)

(

new

)

(

original

Where T_{SINK (new)}is the required maximum heat sink temperature and

T_{SINK (original)}is the heat sink temperature given with the frequency ratings.

A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage

to a peak value (V_rm) of 67% of the maximum grade. If a different grade is being used or V_rmis other than

67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value

obtained from the curves.

11.3 Reverse Recovery Loss by Measurement

This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring

the charge care must be taken to ensure that:

(a) a.c. coupled devices such as current transformers are not affected by prior passage of high

amplitude forward current.

(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope

to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal

damped snubber, connected across diode anode to cathode. The formula used for the calculation

of this snubber is shown below:

V_r

C_S× ^di

R²= 4×

Where: V_r= Commutating source voltage

C_S= Snubber capacitance

= Snubber resistance

12.0 Gate Drive

The recommended pulse gate drive is 30V, 15W with a short-circuit current rise time of not more than

0.5µs. This gate drive must be applied when using the full di/dt capability of the device.

The duration of pulse may need to be configured with respect to the application but should be no shorter

than 20µs, otherwise an increase in pulse current could be needed to supply the resulting increase in

charge to trigger.

Data Sheet. Types N0416SC040-080 Issue 2

Page 5 of 10

September 2014

1 2 3 456 7 8...11

下载PDF

与N0416SC040相关器件

型号	品牌	描述	获取价格	数据表
N0416SC080	LITTELFUSE	Littelfuse提供业界最全面的标准相位控制晶闸管系列之一。器件电压范围在400V至	获取价格
N0416SG020	IXYS	Silicon Controlled Rectifier,	获取价格
N0416SG080	IXYS	Silicon Controlled Rectifier,	获取价格
N-04-18-0-C-LC	MOLEX	101.60mm (4.000") UV Black Cable Tie, 18 Pound Tensile Strength, 100/Bag	获取价格
N-04-18-30-M-LC	MOLEX	101.60mm (4.000") Heat Stabilized Black Cable Tie	获取价格
N-04-18-9-C-LC	MOLEX	101.60mm (4.000) Natural Cable Tie, 18 Pound Tensile Strength, 100/Bag	获取价格