MODEL: MLS
Specify input resistance value for code Z.
[5] OPTIONS (multiple selections)
Multiplication Indicator
■ DC Voltage: -300 – +300 V DC
Minimum span: 10 mV
blank: Without
Offset: Max. 1.5 times span
Input resistance
/E: With (0.0 - 100.0 % display)
Other Options
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
Span ≥ 1 V : ≥ 1 MΩ
blank: none
/Q: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
OUTPUT SPECIFICATIONS
■ DC Current: 0 – 20 mA DC
Minimum span: 1 mA
/C02: Polyurethane coating
Offset: Max. 1.5 times span
/C03: Rubber coating
Load resistance: Output drive 15 V max.
■ DC Voltage: -10 – +12 V DC
Minimum span: 5 mV
TERMINAL SCREW MATERIAL
/S01: Stainless steel
Offset: Max. 1.5 times span
GENERAL SPECIFICATIONS
Construction: Plug-in
Load resistance: Output drive 10 mA max.; 5 mA for
negative voltage output; at ≥ 0.5 V
Connection: M3.5 screw terminals
Screw terminal: Chromated steel (standard) or stainless
steel
INSTALLATION
Power input
Housing material: Flame-resistant resin (black)
Isolation: Input 1 or input 2 to output to power
(Negative sides of the input 1 and 2 must be of the same
potential.)
•AC: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 3 VA
•DC: Operational voltage range: rating ±10 %,
ripple 10 %p-p max., approx. 2 W (80 mA at 24 V)
Operating temperature: -5 to +60°C (23 to 140°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Surface or DIN rail
Overrange output: 0 to 115 % at 1 – 5 V
Zero adjustment: -5 to +5 % (front)
Span adjustment: 95 to 105 % (front)
Equation: Output = K
, K : 0.10 – 1.15 (parameters)
where K × K ≥ 0.2
1
× Input 1 × K × Input 2
2
Weight: 350 g (0.77 lb)
K1
2
1
2
Input 1, Input 2: 0 – 115 %; forcibly limited to 0 % or 115 %
with overrange.
PERFORMANCE in percentage of span
Accuracy: ±0.2 %
Output: 0 – 115 % with K
forcibly limited to 0 % or 115 % with overrange.
0 – [115 × K × K ] % with K × K < 1;
forcibly limited to 0 % or [115 × K × K
, K are ex-factory specified.
[example]
1
× K
2
≥ 1;
Display accuracy: ± (0.2 % of FS + 1 digit)
Temp. coefficient: ±0.02 %/°C (±0.01 %/°F)
Response time: ≤ 0.5 sec. (0 – 90 %)
1
2
1
2
1
2] % with overrange.
Line voltage effect: ±0.1 % over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 2000 V AC @1 minute (input 1 or input 2
to output to power to ground)
K1
2
K
1
K
2
INP1
1.00 1.15 115 % 100 % 115 %
1.00 1.15 100 % 50 % 57.5 %
1.00 1.15 100 % -5 % 0 %
■ DISPLAY (Multiplied values indicator)
INP2
OUT
LCD digital display: 0.0 - 100.0 % (min. digit 0.1 %)
(No scaling)
INPUT SPECIFICATIONS
■ DC Current:
Shunt resistor attached to the input terminals (0.5 W)
MLS SPECIFICATIONS
ES-1644 Rev.5 Page 2/3
http://www.m-system.co.jp/