Datasheet > MHP8565ASS

MHP8565ASS

更新时间： 2023-01-02 17:28:55

品牌	Logo	应用领域
美高森美 - MICROSEMI		/
页数	文件大小	规格书
11页	178K
描述
Switching Regulator

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

MHP8565ASS 数据手册

MHP8565

(Formerly SAT8565 Series)

(Consult Table 3 for Part Number Designations)

Table 4 – SCREENING OPTIONS

COMMERCIAL

COTS

MILITARY

MIL-PRF-38534 Certified

SPACE

MIL-STD-883

Method

TEST

Element Evaluation

N/A

Military

Sample

100%

Space

100%

Note 11

2023

2017

1010

2001

2020

Non-Destruct Wirebond Pull

Pre-Cap Visual

Temperature Cycle

Constant Acceleration

PIND

100%

Pre-Burn In Electrical

100%

(160 Hours)

100%

(320 Hours)

Burn-In

N/A

1015

Final Electrical Tests

Hermeticity (Fine and Gross Leak)

X-Ray (Note 10)

100% (25°C)

100%

N/A

100%

Yes

Note 11

1014

N/A

2012

External Visual

Sample

N/A

100%

Yes

100%

Yes

2009

Certified

NOTES:

1. Most internal components are rated at +10 Volts maximum with some as high as 16V, and are therefore properly

derated for operation at a nominal input of +5 Volts. For use at higher input voltages, please consult factory about

your desired operation voltage and your derating requirements for a check of possible component changes.

2. Internal series switch is self protected and is rated to conduct 4.5 Amps minimum. However, limitations on

internal components plus the characteristics of PWM operation conspire to reduce further the minimum available

output current, especially at output Voltages above Vin/2. Minimum available output current is guaranteed to be

as specified at output Voltage of 2.5 V down to 1.21 V, assuming a clean layout. At output Voltages below 1.21

V, maximum output current may reduce by up to 1 Amp, depending on actual output Voltage, and load regulation

may degrade slightly (up to 1%). At 3.3 V output with a 5 V input, output current reduces by 0.5 A from the value

specified at 2.5 V out.

3. Microsemi does not at this time have a MIL-PRF-38534 qualified radiation hardness assurance program.

4. If not used, or when on, Enable pin should be pulled up to a logic one (2.5V min, 7V max) through a resistor of no

more than 5K Ohms. Voltage on this pin to disable operation needs to be less than 0.13V.

5. Testing is accomplished at an output load of 1A, and at an output Voltage of 2.5V and an input of 5V unless

otherwise specified. Only the specification with post irradiation limits are tested after radiation exposure..

6. Synchronizing pin, if available (see model chart) must be grounded if not used. Consult factory when

contemplating use of frequencies above 580 kHz. Pin input impedance is 40K Ohms.

7. All package outline dimensions are in inches.

8. Consult factory for operation at output voltages below 1.0V. Also see Figure 10.

9. Minimum input voltage is guaranteed by line regulation test.

10. Performed at a DLA approved facility.

11. Tested per MIL-PRF-38534.

T4-LDS-0256 Rev. 4 (121283)

Page 5 of 11

1 2 3 456 7 8...11

下载PDF

与MHP8565ASS相关器件

型号	品牌	描述	获取价格	数据表
MHP8565PC	MICROSEMI	Switching Regulator, Current-mode, 500kHz Switching Freq-Max, MO-078, 5 PIN	获取价格
MHP8565PC-1	MICROSEMI	Switching Regulator, Current-mode, 500kHz Switching Freq-Max, MO-078, 5 PIN	获取价格
MHP8565PC-1C	MICROSEMI	Switching Regulator, Current-mode, 3A, 560kHz Switching Freq-Max, Hybrid	获取价格
MHP8565PC-2	MICROSEMI	Switching Regulator, Current-mode, 500kHz Switching Freq-Max, MO-078, 5 PIN	获取价格
MHP8565PC-3	MICROSEMI	Switching Regulator, Current-mode, 500kHz Switching Freq-Max, MO-078, 5 PIN	获取价格
MHP8565PC-3C	MICROSEMI	Switching Regulator, Current-mode, 3A, 560kHz Switching Freq-Max, Hybrid	获取价格

与MHP8565ASS相关文章

MAX6675资料手册参数详解、引脚配置说明
2024-05-13

4
LM258引脚图及功能介绍、主要参数分析
2024-05-13

2
CD4052资料手册参数详解、引脚配置说明
2024-05-13

3
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
2024-05-13

3

产品中心

服务支持

精选活动

关于我们

帮助中心

MHP8565ASS

MHP8565ASS 数据手册

与MHP8565ASS相关器件

与MHP8565ASS相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

MHP8565ASS

MHP8565ASS 数据手册

与MHP8565ASS相关器件

与MHP8565ASS相关文章

您还可以找

您在本页遇到什么问题？