1 0 MHz t o 5 0 0 MHz VCO Bu ffe r Am p lifie rs
w it h Diffe re n t ia l Ou t p u t s
0/MAX2471
AC ELECTRICAL CHARACTERISTICS—MAX2470 (continued)
(V = +3V, HI/LO = V , all outputs are differentially measured between OUT and OUT driving a 50Ω load through a 180° hybrid,
CC
CC
T
A
= +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
< 500MHz, HI/LO = V
CC
MIN
TYP
1.5:1
1.2:1
75
MAX
UNITS
10MHz < f
10MHz < f
Maximum Output VSWR
(OUT, OUT) (Note 5)
OUT
VSWR
OUT
< 200MHz, HI/LO = GND
OUT
f
= 100MHz
= 500MHz
= 100MHz
= 200MHz
IN
HI/LO = V
CC
f
IN
48
Reverse Isolation
(Note 6)
2
I
IS
dB
12
f
IN
75
HI/LO = GND
f
IN
64
37
f
= 500MHz, HI/LO = V
CC
IN
Isolation OUT to OUT
(Note 7)
dB
45
f
IN
= 200MHz, HI/LO = GND
-26
-30
f
= 500MHz, P
= 200MHz, P
= -5dBm, HI/LO = V
CC
IN
OUT
OUT
Harmonic Suppression
dBc
f
IN
= -5dBm, HI/LO = GND
AC ELECTRICAL CHARACTERISTICS—MAX2471
(Typical values are measured at V = +3V, T = +25°C, unless otherwise noted.) (Note 8)
CC
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Input Frequency Range
(Note 2)
f
IN
10
500
MHz
f
= 10MHz
15.9
16.9
15.6
16
IN
2
Gain (Note 3)
IS
I
f
IN
= 200MHz
dB
21
f
IN
= 500MHz, T = T
A
to T
MAX
11.3
17.8
MIN
Voltage Gain (Note 4)
Noise Figure
A
f
IN
= 10MHz
V/V
dB
V
NF
f
= 500MHz, R
= 50Ω
8.4
OUT
SOURCE
Maximum Output VSWR
(OUT, OUT) (Note 5)
VSWR
10MHz < f
< 500MHz
1.5:1
OUT
OUT
f
= 100MHz
= 500MHz
= 500MHz
74
57
IN
2
I
Reverse Isolation
IS
dB
12
f
IN
f
IN
35
dB
Isolation OUT to OUT (Note 7)
Harmonic Suppression
f
IN
= 500MHz, P
= -5dBm
OUT
-29
dBc
Note 1: Limits are 100% production tested at T = +25°C. Limits over the entire operating temperature range are guaranteed by
A
design and characterization but are not production tested.
Note 2: The part has been characterized over the specified frequency range. Operation outside of this range is possible but not
guaranteed.
Note 3: Gain specified for P
= -5dBm.
OUT
Note 4: Voltage gain measured with no input termination and no output load.
Note 5: Output VSWR is a single-ended measurement for each OUT and OUT.
Note 6: OUT to IN isolation with OUT terminated with 50Ω.
Note 7: Input terminated with 50Ω.
Note 8: Unless otherwise noted: all inputs are differentially measured between IN and IN driven by a 50Ω load through a 180°
hybrid; all outputs are differentially measured between OUT and OUT driving a 50Ω load through a 180° hybrid.
_______________________________________________________________________________________
3