MAFA 2000 Series EDFA
DATASHEET | AUGUST 2012
FIBER OPTICS
Optical/Electrical Characteristics1
Models
2023
Property
Unit
Limit
Comments
2014
2017
2020
2024
2027
Operating Input
Power
Operating Input
Power
Pin (dBm)
Pin (dBm)
Max
Min
12
12
12
12
12
12
Typical
(May vary for some models)
-10
-10
-10
-10
-10
-10
14
+/-.20
17
+/-.20
20
+/-.20
23
+/-.25
24
+/-.20
27
+/-.20
Output Power
Po(dBm)
Nominal
Note 2
Noise Figure
NF (dB)
Gs (dB)
Typ/Max
Max
4.5/5.0 4.5/5.0 4.5/5.0
4.5/5.0
+/-0.5
5.0/5.5
+/-0.5
5.0/5.5
+/-0.5
(Notes 3, 8)
(Notes 4)
Static Gain
Flatness
Dynamic Gain
Flatness
Output Power
Stability
+/-0.5
+/-1.0
+/- 0.2
+/-0.5
+/-1.25
+/- 0.2
+/-0.5
+/-1.5
+/- 0.2
Gd (dB)
(dB)
Max
Max
+/-2.0
+/-2.0
+/-2.0
+/-0.2
(Notes 5, 7)
(Note 6)
+/- 0.2
+/- 0.2
Power
Consumption
(Steady state)
Psys(W)
Max
3
4
8
10
15
25
70oC Case
Notes:
1. Unless stated otherwise, all specifications apply over the full operating temperature and humidity ranges
2. Measurement variations
3. Measured with 8 evenly spread input optical signals @ 25°C, Pin ≈ 0 dBm. Measuring with 1 input optical signal with Pin
≈ 0 dBm and ≈ 1550 nm is also available (Low Noise Figure options with NF <4.0/4.5 dB are available for some models
only)
4. Measured with a swept Probe Signal (Pp), where Pp ≈ 0 dBm @ 25C
5. Measured with a swept Probe Signal (Pp), and a fixed Tone Signal (Pt) @ ~ 1550 nm; (Pt ≈ Pp+20 dB; Pt + Pp ≈ 0 dBm)
@ 25C; Gain Flattened Options with ΔG ≤ +/-0.75dB or ΔG ≤ +/-1.0dB are available (for some models only)
6. Over polarization and temperature
7. Static and Dynamic Gain Flatness for PONA 2130 can be defined for 1545 nm ≤ ≤ 1562 nm and by special request
only.
8. Specific NF and ΔG can be guaranteed at a single specified Input Optical Power Level (Pin = Pt + Pp) equal or different
from 0 dBm.
General and Mechanical Specifications
Property
Requirement
1530 nm ~ 1562 nm
-20C to 75C
Comments
Operating Wavelength
Operating Case Temperature
Storage Temperature
Operating Humidity
Standard
-40C to 85C
20% to 85%
Non-condensing
All versions
Voltage Supply Range
+4.5V to +5.5VDC
SC/APC; SC/UPC; FC/APC;
FC/UPC; E2000/APC
4.9”W x 5.9”D x 0.8”H
4.9”W x 5.9”D x 1.9”H
Optical Connectors
Dimensions (in)
User Specified
MAFA 2014 to MAFA 2023
MAFA 2024 to MAFA 2027
* With a 1” heat sink. (MAFA 2024 and MAFA 2027 require a heat sink to meet operating temperature specifications)
|
REV 2012.08
Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.