LTC4413
Dual 2.6A, 2.5V to 5.5V,
Ideal Diodes in 3mm
× 3mm DFN
FeaTures
DescripTion
The LTC®4413 contains two monolithic ideal diodes,
each capable of supplying up to 2.6A from input voltages
between 2.5V and 5.5V. Each ideal diode uses a 100mΩ
P-channel MOSFET that independently connects INA to
OUTA and INB to OUTB. During normal forward operation
the voltage drop across each of these diodes is regulated
to as low as 28mV. Quiescent current is less than 40µA
for diode currents up to 1A. If either of the output voltages
exceeds its respective input voltages, that MOSFET is
turned off and less than 1µA of reverse current will flow
fromOUTtoIN.MaximumforwardcurrentineachMOSFET
is limited to a constant 2.6A and internal thermal limiting
circuits protect the part during fault conditions.
n
2-Channel Ideal Diode ORing or Load Sharing
Low Loss Replacement for ORing Diodes
Low Forward On-Resistance (100mΩ Max at 3.6V)
Low Reverse Leakage Current (1µA Max)
Small Regulated Forward Voltage (28mV Typ)
2.5V to 5.5V Operating Range
n
n
n
n
n
n
n
n
2.6A Maximum Forward Current
Internal Current Limit and Thermal Protection
Slow Turn-On/Off to Protect Against Inductive
Source Impedance-Induced Voltage Spiking
Ultralow Quiescent Current Consumption, Low
Power Alternative to the LTC4413-1
Status Output to Indicate if Selected Channel is
Conducting
Programmable Channel On/Off
Low Profile (0.75mm) 10-Lead 3mm × 3mm DFN
Package
n
n
Two active-high control pins independently turn off the
two ideal diodes contained within the LTC4413, control-
ling the operation mode as described by Table 1. When
the selected channel is reverse biased, or the LTC4413 is
put into low power standby, a status signal indicates this
condition with a low voltage.
n
n
applicaTions
n
Battery and Wall Adapter Diode ORing in Handheld
A 9µA open-drain STAT pin is used to indicate conduction
status. When terminated to a positive supply through a
470k resistor, the STAT pin can be used to indicate that the
selecteddiodeisconductingwithahighvoltage.Thissignal
can also be used to drive an auxiliary P-channel MOSFET
power switch to control a third alternate power source
when the LTC4413 is not conducting forward current.
Products
n
Backup Battery Diode ORing
n
Power Switching
USB Peripherals
n
n
Uninterruptable Supplies
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and
ThinSOT and PowerPath are trademarks of Linear Technology Corporation. All other trademarks
are the property of their respective owners.
The LTC4413 is housed in a 10-lead DFN package.
LTC4413 vs 1N5817 Schottky
Typical applicaTion
2000
V
CC
ENBA
470k
GND LTC4413
ENBB
STAT IS HIGH WHEN
BAT IS SUPPLYING
LOAD CURRENT
1500
STAT
LTC4413
1000
WALL
ADAPTER
INB
OUTB
(0V TO 5.5V)
10µF
BAT
1N5817
CONTROL CIRCUIT
500
INA
OUTA
TO LOAD
4.7µF
0
200
(mV)
300
400
0
100
4413 TA01
V
FWD
4413 TA01b
4413fd
For more information www.linear.com/LTC4413
1