LTC1968
ELECTRICAL CHARACTERISTICS
unless otherwise noted.
The ● denotes specifications which apply over the full operating
temperature range, otherwise specifications are TA = 25°C. V+ = 5V, VOUTRTN = 2.5V, CAVE = 10µF, VIN = 200mVRMS, VENABLE = 0.5V
SYMBOL
Output Characteristics
OVR Output Voltage Range
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
+
●
●
●
0
V
V
kΩ
Z
Output Impedance
(Note 12)
10
12.5
50
16
OUT
CMRRO
Output Common Mode Rejection
Maximum Differential Output Swing
(Note 13)
250
µV/V
V
Accuracy = 1%, DC Input (Note 14)
1.0
0.9
1.05
V
V
OMAX
●
●
PSRRO
Power Supply Rejection
(Note 9)
250
1000
µV/V
Frequency Response
f
f
1% Additional Gain Error (Note 15)
500
15
kHz
1P
±3dB Frequency (Note 15)
MHz
–3dB
Power Supplies
+
V
Supply Voltage
Supply Current
●
●
4.5
5.5
2.7
V
I
IN1 = 20mV, IN2 = 0V
IN1 = 200mV, IN2 = 0V
2.3
2.4
mA
mA
S
Shutdown Characteristics
I
I
I
Supply Current
V
V
V
= 4.5V
= 4.5V
= 0.5V
●
●
●
0.1
–0.1
–0.5
2.1
10
µA
µA
µA
V
SS
IH
IL
ENABLE
ENABLE
ENABLE
ENABLE Pin Current High
ENABLE Pin Current Low
ENABLE Threshold Voltage
ENABLE Threshold Hysteresis
–1
–3
–0.1
V
V
TH
0.1
V
HYS
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 10: Previous generation RMS-to-DC converters required nonlinear
input stages as well as a nonlinear core. Some parts specify a “DC reversal
error,” combining the effects of input nonlinearity and input offset voltage.
The LTC1968 behavior is simpler to characterize and the input offset
voltage is the only significant source of “DC reversal error.”
Note 2: The inputs (IN1, IN2) are protected by shunt diodes to GND and
+
V . If the inputs are driven beyond the rails, the current should be limited
to less than 10mA.
Note 11: Guaranteed by design.
Note 3: The LTC1968 output (V ) is high impedance and can be
OUT
overdriven, either sinking or sourcing current, to the limits stated.
Note 4: The LTC1968C/LTC1968I are guaranteed functional over the
operating temperature range of –40°C to 85°C.
Note 5: The LTC1968C is guaranteed to meet specified performance from
0°C to 70°C. The LTC1968C is designed, characterized and expected to
meet specified performance from –40°C to 85°C but is not tested nor QA
sampled at these temperatures. The LTC1968I is guaranteed to meet
specified performance from –40°C to 85°C.
Note 12: The LTC1968 is a switched capacitor device and the input/output
impedance is an average impedance over many clock cycles. The input
impedance will not necessarily lead to an attenuation of the input signal
measured. Refer to the Applications Information section titled “Input
Impedance” for more information.
Note 13: The common mode rejection ratios of the LTC1968 are measured
with DC inputs from 50mV to 350mV. The input CMRR is defined as the
change in V measured with the input common mode voltage at 0V and
IOS
+
+
V , divided by V . The output CMRR is defined as the change in V
measured with OUT RTN = 0V and OUT RTN = V – 350mV divided by
V – 350mV.
OOS
Note 6: High speed automatic testing cannot be performed with
+
C
= 10µF. The LTC1968 is 100% tested with C
= 47nF.
AVE
AVE
+
Note 7: The LTC1968 is 100% tested with DC and 10kHz input signals.
Measurements with DC inputs from 50mV to 350mV are used to calculate
Note 14: The LTC1968 input and output voltage swings are limited by
internal clipping. However, its ∆Σ topology is relatively tolerant of
momentary internal clipping.
Note 15: The LTC1968 exploits oversampling and noise shaping to reduce
the quantization noise of internal 1-bit analog-to-digital conversions. At
higher input frequencies, increasingly large portions of this noise are
aliased down to DC. Because the noise is shifted in frequency, it becomes
a low frequency rumble and is only filtered at the expense of increasingly
long settling times. The LTC1968 is inherently wideband, but the output
accuracy is degraded by this aliased noise.
the four parameters: G , V , V and linearity error. Correlation tests
ERR OOS IOS
have shown that the performance limits can be guaranteed with the
additional testing being performed to guarantee proper operation of all
internal circuitry.
Note 8: The LTC1968 is inherently very linear. Unlike older log/antilog
circuits, its behavior is the same with DC and AC inputs, and DC inputs are
used for high speed testing.
Note 9: The power supply rejections of the LTC1968 are measured with
+
DC inputs from 50mV to 350mV. The change in accuracy from V = 4.5V
+
to V = 5.5V is divided by 1V.
1968f
3
5秒后页面跳转
LM317T数据手册解读：产品特性、应用、封装与引脚详解
一文带你了解?DB3二极管好坏判断、参数信息、替代推荐
LM358DR数据手册：引脚说明、电气参数及替换型号推荐
OP07CP数据手册解读：引脚信息、电子参数
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
