5秒后页面跳转
LT3573IMSE#TRPBF PDF预览

LT3573IMSE#TRPBF

更新时间: 2024-02-19 19:00:38
品牌 Logo 应用领域
凌特 - Linear 转换器
页数 文件大小 规格书
26页 271K
描述
LT3573 - Isolated Flyback Converter without an Opto-Coupler; Package: MSOP; Pins: 16; Temperature Range: -40°C to 85°C

LT3573IMSE#TRPBF 技术参数

是否Rohs认证: 符合生命周期:Transferred
零件包装代码:MSOP包装说明:HTSSOP, TSSOP16,.19,20
针数:16Reach Compliance Code:compliant
ECCN代码:EAR99HTS代码:8542.39.00.01
风险等级:5.17模拟集成电路 - 其他类型:SWITCHING REGULATOR
控制模式:CURRENT-MODE最大输入电压:40 V
最小输入电压:3 V标称输入电压:12 V
JESD-30 代码:R-PDSO-G16JESD-609代码:e3
长度:4.039 mm湿度敏感等级:1
功能数量:1端子数量:16
最高工作温度:125 °C最低工作温度:-40 °C
最大输出电流:1.85 A封装主体材料:PLASTIC/EPOXY
封装代码:HTSSOP封装等效代码:TSSOP16,.19,20
封装形状:RECTANGULAR封装形式:SMALL OUTLINE, HEAT SINK/SLUG, THIN PROFILE, SHRINK PITCH
峰值回流温度(摄氏度):260认证状态:Not Qualified
座面最大高度:1.1 mm子类别:Switching Regulator or Controllers
表面贴装:YES切换器配置:BUCK-BOOST
最大切换频率:1000 kHz技术:BIPOLAR
温度等级:AUTOMOTIVE端子面层:Matte Tin (Sn)
端子形式:GULL WING端子节距:0.5 mm
端子位置:DUAL处于峰值回流温度下的最长时间:30
宽度:3 mmBase Number Matches:1

LT3573IMSE#TRPBF 数据手册

 浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第4页浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第5页浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第6页浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第8页浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第9页浏览型号LT3573IMSE#TRPBF的Datasheet PDF文件第10页 
LT3511  
operaTion  
The LT3511 is a current mode switching regulator IC de-  
signed specifically for the isolated flyback topology. The  
keyprobleminisolatedtopologiesishowtocommunicate  
informationregardingtheoutputvoltagefromtheisolated  
secondary side of the transformer to the primary side.  
Historically, optoisolators or extra transformer windings  
communicate this information across the transformer.  
Optoisolator circuits waste output power, and the extra  
components increase the cost and physical size of the  
power supply. Optoisolators can also exhibit trouble due  
to limited dynamic response, nonlinearity, unit-to-unit  
variation and aging over life. Circuits employing an extra  
transformer winding also exhibit deficiencies. Using an  
extra winding adds to the transformer’s physical size and  
cost, and dynamic response is often mediocre.  
VC pin controls the current level just as it does in normal  
current mode operation, but instead of turning the switch  
on at the start of the oscillator period, the part turns on the  
switch when the secondary-side winding current is zero.  
Boundary Mode Operation  
Boundary mode is a variable frequency, current mode  
switching scheme. The switch turns on and the inductor  
current increases until a VC pin controlled current limit.  
After the switch turns off, the voltage on the SW pin rises  
to the output voltage divided by the secondary-to-primary  
transformer turns ratio plus the input voltage. When the  
secondary current through the diode falls to zero, the SW  
. A discontinuous conduction  
pin voltage falls below V  
IN  
mode (DCM) comparator detects this event and turns the  
switch back on.  
In the LT3511, the primary-side flyback pulse provides  
informationabouttheisolatedoutputvoltage. Inthisman-  
ner, neither optoisolator nor extra transformer winding is  
required for regulation. Two resistors program the output  
voltage. Since this IC operates in boundary mode, the part  
calculates output voltage from the switch pin when the  
secondary current is almost zero.  
Boundarymodereturnsthesecondarycurrenttozeroevery  
cycle,soparasiticresistivevoltagedropsdonotcauseload  
regulation errors. Boundary mode also allows the use of a  
smaller transformer compared to continuous conduction  
mode and does not exhibit subharmonic oscillation.  
At low output currents, the LT3511 delays turning on the  
switch, and thus operates in discontinuous mode. Unlike  
traditional flyback converters, the switch has to turn on  
to update the output voltage information. Below 0.6V on  
the VC pin, the current comparator level decreases to  
its minimum value, and the internal oscillator frequency  
decreases. With the decrease of the internal oscillator,  
the part starts to operate in DCM. The output current is  
able to decrease while still allowing a minimum switch off  
time for the flyback error amplifier. The typical minimum  
internal oscillator frequency with VC equal to 0V is 40kHz.  
The Block Diagram shows an overall view of the system.  
Many of the blocks are similar to those found in traditional  
switching regulators including internal bias regulator, os-  
cillator, logic, current amplifier, current comparator, driver,  
and output switch. The novel sections include a special  
flyback error amplifier and a temperature compensation  
circuit. In addition, the logic system contains additional  
logic for boundary mode operation.  
The LT3511 features boundary mode control, where the  
part operates at the boundary between continuous con-  
duction mode and discontinuous conduction mode. The  
3511fa  
7

LT3573IMSE#TRPBF 替代型号

型号 品牌 替代类型 描述 数据表
LT3573IMSE#PBF Linear

功能相似

LT3573 - Isolated Flyback Converter without an Opto-Coupler; Package: MSOP; Pins: 16; Temp

与LT3573IMSE#TRPBF相关器件

型号 品牌 获取价格 描述 数据表
LT3573IMSEPBF Linear

获取价格

Isolated Flyback Converter without an Opto-Coupler
LT3573IMSE-PBF Linear

获取价格

Isolated Flyback Converter Without an Opto-Coupler
LT3573IMSETRPBF Linear

获取价格

Isolated Flyback Converter without an Opto-Coupler
LT3573IMSE-TRPBF Linear

获取价格

Isolated Flyback Converter Without an Opto-Coupler
LT3574 Linear

获取价格

Isolated Flyback Converter Without an Opto-Coupler
LT3574 ADI

获取价格

无需使用光耦合器的隔离型反激式转换器
LT3574EMS Linear

获取价格

Isolated Flyback Converter Without an Opto-Coupler
LT3574EMS#PBF Linear

获取价格

LT3574 - Isolated Flyback Converter Without an Opto-Coupler; Package: MSOP; Pins: 16; Temp
LT3574EMS#TRPBF Linear

获取价格

LT3574 - Isolated Flyback Converter Without an Opto-Coupler; Package: MSOP; Pins: 16; Temp
LT3574EMSPBF Linear

获取价格

Isolated Flyback Converter Without an Opto-Coupler