LM4811
www.ti.com
SNAS119D –DECEMBER 2000–REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
(1)(2)
Absolute Maximum Ratings
Supply Voltage
6.0V
−65°C to +150°C
2.5kV
Storage Temperature
(3)
ESD Susceptibility
(4)
ESD Susceptibility Machine model
Junction Temperature (TJ)
200V
150°C
Vapor Phase (60 sec.)
Infrared (15 sec.)
215°C
Soldering Information
DGS0010A Package
θJA DGS0010A
220°C
194°C/W
52°C/W
θJC DGS0010A
(5)
θJA NGY0010A
63°C/W
Thermal Resistance
θJC NGY0010A(5)
12°C/W
(5)
θJA NHD0010A
63°C/W
(5)
θJC NHD0010A
12°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human body model, 100pF discharged through a 1.5kΩ resistor.
(4) Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200pF cap is charged to the specified voltage, then
discharged directly into the IC with no external series resistor (resistance of discharge path must be under 50 Ohms).
(5) The NGY0010A or NHD0010A package has its Exposed−DAP soldered to an exposed 2in2 area of 1oz printed circuit board copper.
Operating Ratings
Temperature Range
TMIN ≤ TA ≤ TMAX
−40°C ≤ T A ≤ 85°C
2.0V ≤ VCC ≤ 5.5V
Supply Voltage
(1)(2)
Electrical Characteristics
The following specifications apply for VDD = 5V unless otherwise specified, limits apply to TA = 25°C.
LM4811
Units
(Limits)
Parameter
Test Conditions
Typ(3)
Limit
(4)
VDD
Supply Voltage
2.0
5.5
3.0
V (min)
V (max)
mA
IDD
ISD
VOS
PO
Supply Current
VIN = 0V, IO = 0A
1.3
0.3
4.0
Shutdown Current
Output Offset Voltage
Output Power
VIN = 0V
µA
VIN = 0V
50
mV
0.1% THD+N; f = 1kHz
RL = 16Ω
105
70
mW
mW
%
RL = 32Ω
THD+N
Crosstalk
PSRR
VIH
Total Harmonic Distortion
Channel Separation
PO = 50mW, RL = 32Ω
f = 20Hz to 20kHz
0.3
RL = 32Ω; f = 1kHz;
PO = 70mW
100
60
dB
dB
Power Supply Rejection Ratio
CB = 1.0µF, VRIPPLE = 100mVPP
f = 217Hz
(CLOCK, UP/DN, SHUTDOWN)
Input Voltage High
1.4
V (min)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
(2) All voltages are measured with respect to the ground pin, unless otherwise specified.
(3) Typical specifications are specified at +25°C and represent the most likely parametric norm.
(4) Tested limits are ensured to TI's AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are ensured by design,
test, or statistical analysis.
Copyright © 2000–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM4811