LM317M, LM317MA
MAXIMUM RATINGS (T = 25°C, unless otherwise noted.)
A
Rating
Symbol
V –V
Value
Unit
Input–Output Voltage Differential
40
Vdc
I
O
Power Dissipation (Package Limitation) (Note 1)
Plastic Package, T Suffix
T
A
= 25°C
P
Internally Limited
D
Thermal Resistance, Junction–to–Air
Thermal Resistance, Junction–to–Case
θ
θ
70
5.0
°C/W
°C/W
JA
JC
Plastic Package, DT Suffix
= 25°C
T
A
P
θ
θ
Internally Limited
D
JA
JC
Thermal Resistance, Junction–to–Air
Thermal Resistance, Junction–to–Case
92
5.0
°C/W
°C/W
Operating Junction Temperature Range
Storage Temperature Range
T
–40 to +125
–65 to +150
°C
°C
J
T
stg
NOTE: 1. Figure 23 provides thermal resistance versus pc board pad size.
ELECTRICAL CHARACTERISTICS (V –V = 5.0 V; I = 0.1 A, T = T
to T [Note 1], unless otherwise noted.)
high
I
O
O
J
low
Characteristics
Figure
Symbol
Min
Typ
Max
Unit
Line Regulation (Note 2)
= 25°C, 3.0 V ≤ V –V ≤ 40 V
1
Reg
–
0.01
0.04
%/V
line
T
A
I
O
Load Regulation (Note 2)
= 25°C, 10 mA ≤ I ≤ 0.5 A
2
Reg
load
T
A
O
V
O
O
≤ 5.0 V
≥ 5.0 V
–
–
5.0
0.1
25
0.5
mV
V
% V
O
Adjustment Pin Current
3
I
–
–
50
100
5.0
µA
µA
Adj
Adjustment Pin Current Change
1,2
∆I
0.2
Adj
2.5 V ≤ V –V ≤ 40 V, 10 mA ≤ I ≤ 0.5 A, P ≤ P
I
O
L
D
max
Reference Voltage
3.0 V ≤ V –V ≤ 40 V, 10 mA ≤ I ≤ 0.5 A, P ≤ P
max
LM317M:
LM317MA:
3
1
2
V
1.200
1.225
1.250
1.250
1.300
1.275
V
ref
I
O
O
D
Line Regulation (Note 2)
3.0 V ≤ V –V ≤ 40 V
Reg
–
0.02
0.07
%/V
line
I
O
Load Regulation (Note 2)
10 mA ≤ I ≤ 0.5 A
Reg
load
O
V
O
V
O
≤ 5.0 V
≥ 5.0 V
–
–
20
0.3
70
1.5
mV
% V
O
Temperature Stability (T
≤ T ≤ T
)
3
3
T
–
–
0.7
3.5
–
% V
low
J
high
S
O
Minimum Load Current to Maintain Regulation
(V –V = 40 V)
I
10
mA
A
Lmin
I
O
Maximum Output Current
3
I
max
V –V ≤ 15 V, P ≤ P
0.5
0.15
0.9
0.25
–
–
I
I
O
O
D
D
max
max
V –V = 40 V, P ≤ P
, T = 25°C
A
RMS Noise, % of V
T = 25°C, 10 Hz ≤ f ≤ 10 kHz
A
–
4
N
–
0.003
–
% V
O
O
Ripple Rejection, V = 10 V, f = 120 Hz (Note 3)
RR
dB
O
Without C
–
66
65
80
–
–
Adj
C
= 10 µF
Adj
Long–Term Stability, T = T
T = 25°C for Endpoint Measurements
A
(Note 4)
3
S
–
0.3
1.0
%/1.0 k
Hrs.
J
high
NOTES: 1. T
low
to T
high
= 0° to +125°C for LM317M
T
to T
= –40° to +125°C for LM317MB
low
high
2. Load and line regulation are specified at constant junction temperature. Changes in V due to heating effects must be taken into account separately.
O
Pulse testing with low duty cycle is used.
3. C , when used, is connected between the adjustment pin and ground.
Adj
4. Since Long–Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average stability
from lot to lot.
2
MOTOROLA ANALOG IC DEVICE DATA