LM193, LM193A, LM293, LM293A, LM393, LM393A
Electrical Characteristics
4
Electrical Characteristics
+
-
Table 3.
V
= +5V, V = 0V, T
= +25°C (unless otherwise specified)
CC
CC
amb
LM193A - LM293A
LM393A
LM193- LM293
LM393
Symbol
Parameter
Unit
Min. Typ.
Max.
Min Typ.
Max.
(1)
Input Offset Voltage - note
= +25°C
V
T
1
2
4
1
5
9
mV
nA
io
amb
T
≤ T
≤ T
min
amb
max
Input Offset Current
= +25°C
I
I
T
3
25
100
5
50
150
io
amb
T
≤ T
≤ T
min
amb
max
+
-
(2)
Input Bias Current (I or I ) - note
= +25°C
T
25
100
300
25
250
400
nA
V/mV
mA
ib
amb
T
≤ T
≤ T
min
amb max
Large Signal Voltage Gain
= 15V, R = 15kΩ, V = 1V to 11V
A
vd
V
50
200
50
200
CC
L
o
Supply Current (all comparators)
V
V
I
= +5V, no load
= +30V, no load
0.4
1
1
2.5
0.4
1
1
2.5
CC
CC
CC
(3)
Input Common Mode Voltage Range - note
V
= 30V
= +25°C
CC
V
V
+
+
icm
T
0
0
V
V
-1.5
-2
0
0
V
V
-1.5
-2
amb
CC
CC
+
+
T
≤ T
≤ T
min
amb
max
CC
CC
(4)
+
+
V
Differential Input Voltage -note
V
V
CC
id
CC
Low Level Output Voltage
V
= -1V, I
= +25°C
= 4mA
id
sink
V
mV
OL
T
250
0.1
400
700
250
0.1
400
700
amb
T
≤ T
≤ T
min
amb max
High Level Output Current (V = 1V)
V
id
= V = 30V
CC
o
I
OH
T
= +25°C
nA
amb
T
≤ T
≤ T
1
1
µA
min
amb
max
Output Sink Current
V = 1V, V = 1.5V
I
mA
SINK
6
16
6
16
id
o
(5)
Response Time - note
R = 5.1kΩ connected to V
tre
µs
+
1.3
1.3
L
CC
Large Signal Response Time
+
trel
R = 5.1kΩ connected to V
(ref)
, e = TTL,
ns
L
CC
l
V
= +1.4v
300
300
+
1. At output switch point, Vo ≈ 1.4V, Rs = 0 with VCC+ from 5V to 30V, and over the full common-mode range (0V to VCC
-
1.5V).
2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant,
independent of the state of the output, so no loading charge exists on the reference of input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The
upper end of the common-mode voltage range is VCC+ -1.5V, but either or both inputs can go to +30V without damage.
4. The response time specified is for a 100mV input step with 5mV overdrive. For larger overdrive signals 300ns can be
obtained.
5. Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the
common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than -
0.3V (or 0.3V bellow the negative power supply, if used).
5/15