FIG 1
REVISION AC
(IPBT-108-H1-XX-D SHOWN)
IPBT-1XX-XX-XX-D-XX
OPTION
No OF POSITIONS
-02 THRU -15
(No OF POSITIONS x .165[4.19]) + .053[1.33] REF
(No OF POSITIONS - 1) x .165[4.19]
-RA: RIGHT ANGLE (SEE FIG 2, SHEET 2)
[STYLE -H1 ONLY]
.109 2.76 REF
DO NOT
SCALE FROM
THIS PRINT
(PER ROW)
-GP: GUIDE POSTS (USE IPBT-XX-D-GP,
SEE FIG 4, SHEET 3)
-02 (SEE SHEET 5, FIG.8)
(NOT AVAILABLE W/ -K OPTION)
*-K: KEYED POLARIZATION
01
02
LEAD STYLE
(USE IPBT-XX-D-K)(SEE FIG 9, SHEET 5)
(NOT AVAILABLE W/ -GP OPTION)
-H1: HIGH POWER, THRU HOLE
(USE T-1S55-XX-X-2, SEE FIG.1, SHEET 1)
-H2: HIGH POWER, SURFACE MOUNT
(USE T-1S55-02-X-2, SEE FIG.3, SHEET 3)
-H3: HIGH POWER. THRU HOLE, .670" STACKER
(USE T-1S55-05-X-2, SEE FIG.5, SHEET 4)
-H4: HIGH POWER. THRU HOLE, .748" STACKER
(USE T-1S55-06-X-2, SEE FIG.6, SHEET 4)
-H5: HIGH POWER. THRU HOLE, .787" STACKER
(USE T-1S55-07-X-2, SEE FIG.6, SHEET 4)
-H6: HIGH POWER. THRU HOLE, .984" STACKER
(USE T-1S55-08-X-2, SEE FIG.6, SHEET 4)
*(LEAVE BLANK FOR NO KEY OPTION,
SAMTEC WILL ONLY SUPPORT EXISTING
BUSINESS AS OF REV W)
.378 9.60 REF
.050 1.27 REF
.165 4.19
ROW SPECIFICATION
-D: DOUBLE (USE IPBT-XX-D)
09
PLATING SPECIFICATION
C
L
-TM: MATTE TIN CONTACT AND TAIL
(USE T-1S55-XX-T-2)
-T: MATTE TIN CONTACT AND TAIL
(USE T-1S55-XX-T-2)
IPBT-08-D
SEE NOTE 8
.205 5.21 REF
"A"
.424 10.77
REF
.260 6.60
.380 9.65
REF
.405 10.29
REF
REF
.510 12.95
REF
.130 3.30
"A"
.045 1.14 SQ REF
.165 4.19
2
MAX SWAY
T-1S55-01-X-2
2
MAX SWAY
.045 1.14 SQ REF
(TYP)
.165 4.19
(TYP)
SECTION "A"-"A"
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. COPLANARITY (FOR SURFACE MOUNT): SEE TABLE 2 SHEET 3.
3. MAX BURR ALLOWANCE: .0015 [.038]
(No OF POSITIONS - 1) x .165[4.19] ±.008[0.20]
4. MINIMUM TERMINAL RETENTION: 1 LB.
5. IPBT-XX-D-XX AND IPBV-XX-D PARTS TO BE MOLDED TO POSITION,
IPBE-XX-XX-D ARE TO BE CUT.
6. MAX HEIGHT VARIATION BETWEEN PINS: .005 [.13]
7. ALL PIN TO PIN DIMENSIONS TO BE MEASURED FROM TIP TO TIP.
8. THIS NUMBER REPRESENTS THE NUMBER OF POSITIONS PER ROW ONLY
AND IS NOT INTENDED TO BE USED IN POSITION NUMBERING.
9. ALL PARTS TO BE PACKAGED IN TUBES EXCEPT 2 AND 3 POS. 2 AND 3 POS
PARTS TO BE LAYER PACKAGED.
10. MAX CUT FLASH: .005 [.13]
11. AFTER REVISION T OF COMPONENT PRINT IPT1-XX-D-XX-X, SAMTEC LOGO
TO APPEAR ON CORE #1 FOR POSITIONS 1 THROUH 5. FOR POSITIONS 6
THROUGH 15, LOGO TO APPEAR ON CORE #1 AND THE LAST CORE WITHIN THE SAME ROW.
UNLESS OTHERWISE SPECIFIED,
PROPRIETARY NOTE
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
DECIMALS
ANGLES
2
.XX: .01[.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .005[.13]
.XXXX: .0020[.051]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
CONSENT OF SAMTEC, INC.
e-Mail info@SAMTEC.com
DESCRIPTION:
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
.165 DOUBLE ROW TERMINAL ASSEMBLY
INSULATOR: LCP UL 94 VO, COLOR: BLACK
TERMINAL: HIGH COPPER ALLOY
DWG. NO.
IPBT-1XX-XX-XX-D-XX
BY:
DEAN P
7/27/2001
SHEET 1 OF 5
F:\DWG\MISC\MKTG\IPBT-1XX-XX-XX-D-XX-MKT.SLDDRW
5秒后页面跳转
PAM8403音频功率放大器：资料手册参数分析
LAN8720以太网收发器：资料手册参数分析
SI2301 N沟道MOSFET：资料手册参数分析
ADC0809逐次逼近寄存器型模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
