REVISION H
HQDPR-XXX-XX.X-XXX-XXX-X-X
END OPTION
-F: SCREW OPTION FIRST END ONLY
-S: SCREW OPTION SECOND END ONLY
-B: SCREW OPTION BOTH ENDS
-N: NO CAPS
No OF PAIRS
-020, -040, -060, -080
(PER ROW)
FIG 1
VERTICAL
(HQDPR-040-XX.X-STR-STR-1 SHOWN)
(SEE FIG. 3, SHEET 5 FOR EDGE MOUNT
END OPTIONS)
(SEE FIG. 4, SHEET 5 FOR DOUBLE
VERTICAL END OPTIONS)
(SEE FIG. 5, SHEET 5 FOR NO CAPS OPTIONS)
(LEAVE BLANK FOR STANDARD CAPS
BOTH ENDS)
LENGTH
-XX.X (INCHES)
(1.72[43.7] MIN -
40.0[1016.0] MAX)
(SEE NOTE 2)
LENGTH: XX.X + "L" REF (SEE TABLE 4)
LENGTH: XX.X 1%
FIRST END
-TTR: TERMINAL, TOP, RIGHT
-TTL: TERMINAL, TOP, LEFT
-TBR: TERMINAL, BOTTOM, RIGHT
-TBL: TERMINAL, BOTTOM, LEFT
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 2)
WIRING OPTION
-1: PIN 1 TO PIN 1
-2: PIN 1 TO PIN 2
-3: PIN 1 TO PIN N-3
-4: PIN 1 TO PIN N-2
(SEE TABLE 10, SHEET 6)
01
02
01
02
'A'
SECOND END
"A" REF
(TYP)
-TTR: TERMINAL, TOP, RIGHT
-TTL: TERMINAL, TOP, LEFT
-TBR: TERMINAL, BOTTOM, RIGHT
-TBL: TERMINAL, BOTTOM, LEFT
-STR: SOCKET, TOP, RIGHT
-STL: SOCKET, TOP, LEFT
-SBR: SOCKET, BOTTOM, RIGHT
-SBL: SOCKET, BOTTOM, LEFT
(SEE TABLE 1 & SHEET 3)
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
"B" REF
(TYP)
SUB-HQCD-X-XXX-XX-XX
-TEU: TERMINAL, EDGE MOUNT, UP
-TED: TERMINAL, EDGE MOUNT, DOWN
-SEU: SOCKET, EDGE MOUNT, UP
-SED: SOCKET, EDGE MOUNT, DOWN
(SEE TABLE 5 & SHEET 4)
'B'
ADD UV EPOXY TO TOP OF JACKET
AND SHIELD AT ALL LOCATIONS.
DO NOT LET EPOXY FLOW
N-1
(SEE TABLE 3)
N
(SEE TABLE 3)
SEE NOTE 7
OFF THE SIDE OF THE SHIELD
STS-01
(TIGHTEN TO 1.4-1.7 IN-LBS)
(4 PLCS)
.565 14.35
REF (TYP)
N
N-1
.775 19.68
REF (TYP)
(SEE TABLE 3)
(SEE TABLE 3)
HDRL-11
(SEE NOTE 5)
FIRST END
.253 6.43 REF (TYP)
QCD-XX-01
* "C" REF
SECOND END
DETAIL 'A'
SCALE 4 : 1
SUB-TTC-10-01-075-XX.XX
(SEE TABLE 1 FOR QTY)
NOTES:
QCD-XX-02
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. SUB-TTC LENGTH IS EQUAL TO HQDPR LENGTH.
C2 3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
FOR SHORTS AND OPENS.
C3 4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
5. TOP SUB-TTC NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11
TO BE CENTERED ON LOWER SUB-TTC AS SHOWN; HDRL-11 IS
TO CONTAIN PART NUMBER, SHOP NUMBER & DATE CODE.
6. PACKAGE ASSEMBLIES IN STATIC DISSIPATIVE BAGS.
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
SEE NOTE 7
Pb
DETAIL 'B'
SCALE 4 : 1
* -DV END OPTIONS ONLY
7. SHIFT CABLE TOWARD PIN 1 POSITION ON EACH ROW OF EACH END - TOP AND BOTTOM.
8. PARTS TO BE PROCESSED PER SAMTEC ACCEPTABLILITY REQUIREMENTS:
HDR-PI-01 "CABLE ASSEMBLY WORKMANSHIP STANDARDS".
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
9. CABLE ASSEMBLY FOLLOWS QXH-DP PINOUT. EVERY THIRD PIN IS NOT CONNECTED.
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XXX: .005 [.13]
.XXXX: .0020 [.051]
SHEET SCALE: 1:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
0.5mm HIGH-SPEED TWIN-AX CABLE ASSEMBLY
DWG. NO.
HQDPR-XXX-XX.X-XXX-XXX-X-X
BY:
ANDREW C 04/29/2008 SHEET 1 OF
F:\DWG\MISC\MKTG\HQDPR-XXX-XX.X-XXX-XXX-X-X-MKT.SLDDRW
5秒后页面跳转
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
74HC573三态非易失锁存器(Latch)资料手册参数分析
MAX3232 RS-232电平转换器资料手册参数分析
MAX485 RS-485/RS-422收发器资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
