G, GN
Vishay Dale
www.vishay.com
DIMENSIONS in inches [millimeters]
1.50
L
[38.10] (1)
min.
D
L1
C
DIMENSIONS in inches [millimeters]
GLOBAL
MODEL
L
(2)
L1 max.
C
D
Gꢀꢀ1...8ꢀ
0.250 0.031
[6.35 0.787]
0.281
[7.14]
0.085 0.020
[2.16 0.508]
0.020 0.002
[0.508 0.051]
Gꢀꢀ1...ꢂ8ꢀ
0.312 0.016
[7.92 0.406]
0.328
[8.33]
0.078 + 0.016 - 0.031
[1.98 + 0.406 - 0.787]
0.020 0.002
[0.508 0.051]
Gꢀꢀ2
Gꢀꢀꢂ...8ꢀ
0.406 0.031
[10.31 0.787]
0.437
[11.10]
0.094 0.031
[2.39 0.787]
0.020 0.002
[0.508 0.051]
Gꢀꢀꢂ...ꢂ8ꢀ
0.562 0.062
[14.27 1.57]
0.622
0.188 0.032
[4.78 0.813]
0.032 0.002
[0.813 0.051]
Gꢀꢀ5
Gꢀ5C
Gꢀ1ꢀ
[15.80]
0.500 0.062
[12.70 1.57]
0.593
[15.06]
0.218 0.032
[5.54 0.813]
0.040 0.002
[1.02 0.051]
0.875 0.062
[22.23 1.57]
1.0
[25.4]
0.312 0.032
[7.92 0.813]
0.040 0.002
[1.02 0.051]
Notes
(1)
(2)
On some standard reel pack methods, the leads may be trimmed to a shorter length than shown
L1 max. dimension is clean lead to clean lead
MATERIAL SPECIFICATIONS
Element: Copper-nickel alloy or nickel-chrome alloy,
depending on resistance value
Core: Ceramic, beryllium oxide or alumina, depending on
resistor model
Coating: Special high temperature silicone
Standard Terminals: 100 % Sn, or 60/40 Sn/Pb coated
Copperweld®
DERATING
120
100
80
60
40
20
CHAR. V
End Caps: Stainless steel
Part Marking: DALE, model, wattage (3), value, tolerance,
date code
Note
CHAR. U
(3)
Wattage marked on part will be “U” characteristic
0
GN NON-INDUCTIVE
- 65 - 50
0
50
150
250
350
25
AMBIENT TEMPERATURE IN °C
Models of equivalent physical and electrical specifications
are available with non-inductive (Ayrton-Perry) winding.
They are identified by inserting the letter N after G in the
model number (GN005, for example). Two conditions apply:
TERMINATION
When G resistors will be operated at full rated power,
resistance welding or high temperature solder are the
recommended termination methods. Termination should be
made within 1/2" from end of resistor body.
1. For GN models, divide maximum resistance values by two
2. Body O.D. on GN05C may exceed that of the G05C by
0.010"
PERFORMANCE
TEST LIMITS
TEST
CONDITIONS OF TEST
CHARACTERISTIC U CHARACTERISTIC V
Thermal Shock
Rated power applied until thermally stable, then a min. of 15 min at -55 °C (0.2 % + 0.05
)
R
R
(2.0 % + 0.05
)
R
R
Short Time Overload
5x power (G001...80 thru G05C), 10 x power (G010) for 5 s
(0.2 % + 0.05
)
(2.0 % + 0.05 )
Dielectric Withstanding
500 VRMS minimum for G001...80 thru G003...380,
(0.1 % + 0.05
)
R
(0.1 % + 0.05
)
R
Voltage
1000 VRMS minimum for all others, duration of 1 min
-65 °C for 24 h
Low Temperature Storage
(0.2 % + 0.05
(0.5 % + 0.05
(0.2 % + 0.05
(0.1 % + 0.05
(0.1 % + 0.05
(0.5 % + 0.05
)
R
R
R
R
R
R
(2.0 % + 0.05
(2.0 % + 0.05
(2.0 % + 0.05
(0.2 % + 0.05
(0.2 % + 0.05
(3.0 % + 0.05
)
R
R
R
R
R
R
High Temperature Exposure 250 h at +250 °C (characteristic U)
)
)
Moisture Resistance
Shock, Specified Pulse
Vibration, High Frequency
Load Life
MIL-STD-202 Method 106, 7b not applicable
)
)
MIL-STD-202 Method 213, 100 g's for 6 ms, 10 shocks
Frequency varied 10 Hz to 2000 Hz, 20 g peak, 2 directions 6 h each
2000 h at rated power, +25 °C, 1.5 h “ON”, 0.5 h “OFF”
)
)
)
)
)
)
Pull test -5 s to 10 s, 5 lb (G001...80 thru G05C), 10 lb for all others;
torsion test - 3 alternating directions, 360° each
Terminal Strength
(0.1 % + 0.05
)
R
(1.0 % + 0.05 ) R
Revision: 15-Nov-17
Document Number: 30205
2
For technical questions, contact: ww2aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000