Document 574-1
For 30 Watt
Forward-Mode Transformers Telecommunications
• Designed to meet 30 W PoE IEEE 802.3at-2009 standard.
• Operates at 250 kHz with 36–72 Volts input.
• 1500 Vrms, one minute isolation, primary and bias to secondary
• Bias winding output: 12 V; sync winding output: 5 V
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight 10.1 – 10.7 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel Plastic tape: 44 mm wide, 0.4 mm thick,
32 mm pocket spacing, 12.0 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
Leakage
Recommended
output
DCR max (mOhms)3
Turns ratio5
Part
Inductance2
inductance4
number1 min (µH)
pri
sec
bias
sync max (µH) pri : sec pri : bias pri : sync
Output
inductor6
FCT1-33D3SL_ 72.9
FCT1-50D3SL_ 72.9
FCT1-120D3SL_ 72.9
FCT1-195D3SL_ 72.9
FCT1-240D3SL_ 72.9
27.5
27.5
27.5
27.5
27.5
5.0
10.0
28.5
32.0
72.5
250
250
250
235
235
160
160
160
120
120
0.425
0.420
0.175
0.235
0.235
1:0.33
1:0.44
1:1
1:1
1:1
1:1
1:0.56
1:0.56
1:0.56
3.3 V, 9 A SER2013-472
5 V, 6 A SER1360-103
12 V, 2.5 A MSS1278-563
1:1.44 1:0.88 1:0.44 19.5 V, 1.55 A MSS1278-154
1:1.78 1:0.88 1:0.44
24 V, 1.25 A MSS1278-224
1. When ordering, please specify termination and packaging codes:
11
1
2
FCT1-240D3SLD
Output
inductor
12
Sec
10
Termination: L = RoHS tin-silver over tin over nickel over phos bronze.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Pri
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
4
3
tape (175 parts per full reel).
9
8
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
5
Bias
6
Sync
7
2. Inductance is measured at 250 kHz, 0.2 Vrms, 0 Adc.
3. DCR for the primary and secondary is with the windings connected in
parallel.
4. Leakage inductance is for the primary windings with the secondary
windings shorted.
5. Turns ratio is with the primary windings and the secondary windings
connected in parallel.
6. These inductors are recommended for 30% ripple current. Ripple less
than 30% may require the use of physically larger inductors. Allowing
higher ripple current to make use of smaller inductors may create a risk
of discontinuous output current.
The primary windings and the
secondary windings are to be
connected in parallel on the
PC board.
7. Operating temperature range –40°C to +125°C.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 574-1 Revised 10/28/08
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.