THICK FILM SIP NETWORKS
RESISTORSCAPACITORSCOILSDELAY LINES
.
RCD CL101S
←
High density 70-mil pin spacing, an RCD exclusive!
CL SERIES - Low Profile
.
RCD C101
.
RCD CL101
C SERIES - High Power
Term.W
Low cost! Widest selection in the industry!
is Pb-free
and RoHS
compliant
Low profile CL Series available from stock
RoHS
OPTION V - +200°C temperature Range
OPTION S - Super high density (.070” pin spacing)
OPTION P - Pulse tolerant design
OPTION N - Narrowline design (.070” thick)
OPTION F - Flameproof coating
(config.1 & 2, 6-pin,8-pin,and 10-pin)
Wide resistance range: 10Ω to 3MΩ
Available on tape & reel
4-pin through 14-pin standard (2 through 20-pin available)
R/2R Ladder Networks (Config. 7) offer 1/2LSB accuracy
from 4 to 10 bits
OPTION C - Copper alloy terminals
Available in custom circuits with multiple values/capacitors/diodes,
increased power & voltage, tolerance & TC matching, longer pins,
special marking, military screening, resis. values 1Ω to 1000M, etc.
STANDARD CONFIGURATIONS
Std. Config. No.2 (Global Config.B)
Std. Config. No.1 (Global Config.A)
DIMENSIONS
.
.
.
.
.
.
.
→
←
.095 [2.4] Max.
Opt. N= .070±.008
[1.8±.2]
←
Max length=0.1” x No. of pins
→
1
↑
C=.315 [8] Max.
Pin #1
CL=.195 [5] Max.
.008
[.2]
Min
↓
Standard Configuration No. 3
Standard Configuration No. 4
↑
.102 [2.6] Min.
.011 [.28]
→ ←
.
.
.
.
.
.
.
↓
R2
R2
.
.
.
.
.
.
R2
R2
R2
R2
.
.
R1
.
R1
.
R1
.
R1
Dimensions: Inch [mm]
.020 [.5]→ ←
→
←
.100 ± .01 [2.54 ± .25] Opt.
S=.070± .01 [1.78 ±.25]
R1
1 R1
1
.
.
.
.
.
.
SINGLE RESISTOR
POWER RATING*
PACKAGE POWER RATING*
RCD
Type
Std. Configuration No. 5
Std. Configuration No. 6
vvv
vvv
Std. Config. No.7 R/2R
Config.
Config. Config.
4-Pin 6-Pin 7-Pin 8-Pin 9-Pin 10-Pin 12-Pin
1,3,4,5,6
2
3, 7
R
R
R
vvv
vvv
vvv
vvv vvv
C
.3W
.5W
.3W
.17W
1W 1.5W 1.75W 2W 2.25W 2.5W
2W
3W
2R 2R
2R
2R 2R
1
1
1
CL
.2W
.125W** .5W 1W 1.25W 1.5W 1.75W
2.5W
* 25 deg C. Reduce wattage ratings by 1/3 for Opt.S **Config. 7 n/a in CL Series
GND LSB
MSB OUT
STANDARD VALUES- Config. 1, 2, 4, 5, 6:
DERATING (Series C and CL)
DERATING (Option V)
22Ω to 1M* in E-24 values (preferred values in bold type)-
120
100
80
60
40
20
0
120
100
80
60
40
20
0
10, 11, 12, 13, 15, 16, 18, 20, 22, 24, 27, 30, 33, 36, 39, 43, 47,
51, 56, 62, 68, 75, 82, 91 *non-standard values 10Ω to 3M avail.
STANDARD VALUES - Config. 3, Dual Terminator, R1/R2
81Ω/130Ω
160Ω/260Ω
220Ω/270Ω
330Ω/470Ω
25 40
80 120 160 200 240
25
50
75 100
125 150
120Ω/195Ω
121Ω/195Ω
162Ω/260Ω
180Ω/390Ω
220Ω/330Ω
330Ω/390Ω
330Ω/680Ω
3KΩ/6.2KΩ
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
R/2R LADDER NETWORKS (Config.7): 4Bit/6-pin, 5Bit/7-pin,
6Bit/8-pin, 7Bit/9-pin, 8Bit/10-pin, 9Bit/11-pin, and 10Bit/12-pin. Available
in Series C (low profile Series CL n/a). Linearity accuracy is 1/2LSB.
Standard values are 5KΩ, 10KΩ, 25KΩ, 50KΩ, & 100KΩ ±2%.
TYPICAL PERFORMANCE SPECIFICATIONS
Standard Tolerance
Temperature Coefficient
TCR Tracking
2% >=100Ω , 5% <100Ω (1% avail.)
±100ppm typ (±250ppm <50Ω & >2.2M)
50PPM typical
Operating Temperature
Max. Working Voltage
Short Time Overload
Resistance to Solder Heat
Moisture Resistance
Terminal Strength
Thermal Shock
-55°C to +125°C (+200°C Opt.V)
P/N DESIGNATION:
CL= low profile (std), C= high power
CL 08 2
- 102 - G B
W
200V Series C, 100V Series CL & Opt.S
±0.5% (2.5x rated V, 5S, nte 2xW)
Number of Pins
±0.25% (350°C, 5S)
Configuration Number
±1%
Options: V, S, P, N, F, C (leave blank if std)
Resis.Code 1%: 3 signif. figures & multiplier,
±0.25%
(e.g. 10R0=10Ω, 1000=100Ω, 1001=1K, 1004=1M)
Resis.Code 2%-5%: 2 signif. figures & multiplier,
(e.g. 100=10Ω, 101=100Ω, 102=1K, 103=10K, 104=100K,
105=1M). When comprised of 2 res.values (config.3&7) separate
with /, e.g. 181/391=180Ω/390Ω; use 4-digit code when needed
e.g. 1620/261=162Ω/260Ω
±0.5%
Load Life (1000 hours)
Temperature Cycling
Shock and Vibration
Lead Solderability
Marking*
±1.0%
±0.5%
±0.25%
Meets MIL-R-83401
Tolerance Code: G=2% (standard), F=1%, J=5%
Pin #1 ID, resis value, & tol as minimum*
Solder plated steel typ., copper alloy avail**
Packaging: B=Bulk, A3=3 pin taping Ammo pack, M=Magazine Tube
Opt. TC: 50=50ppm,101=100ppm (leave blank if standard)
Termination: W= RoHS compliant (std), Q= Tin/Lead (leave blank if both acceptable)
Terminals
*Parts may be marked with Std or Global configuration code
** RCD recommends use of copper alloy terminals (opt. C) in aqueous cleaning systems
-
-
-
-
RCD Components Inc, 520 E.Industrial Park Dr, Manchester, NH, USA 03109 rcdcomponents.com Tel: 603 669 0054 Fax: 603 669 5455 Email:sales@rcdcomponents.com
FA032D Sale of this product is in accordance with GF-061. Specifications subject to change without notice.
38