5秒后页面跳转
捷配首页

Datasheet > 信号电路 > 运动控制电子器件> BA6219BFP-Y-DX
BA6219BFP-Y-DX PDF预览

BA6219BFP-Y-DX

更新时间： 2024-02-23 12:26:29
品牌 Logo 应用领域
罗姆 - ROHM 驱动器电机
页数 文件大小 规格书
7页 110K
描述
Brush DC Motor Controller, 2.2A, PDSO25, POWER, HSOP-25

阅读下载

获取价格

BA6219BFP-Y-DX 技术参数

生命周期：Obsolete零件包装代码：SOIC
包装说明：HSSOP,针数：25
Reach Compliance Code：unknownECCN代码：EAR99
HTS代码：8542.39.00.01风险等级：5.62
模拟集成电路 - 其他类型：BRUSH DC MOTOR CONTROLLERJESD-30 代码：R-PDSO-G25
长度：13.6 mm功能数量：1
端子数量：25最大输出电流：2.2 A
封装主体材料：PLASTIC/EPOXY封装代码：HSSOP
封装形状：RECTANGULAR封装形式：SMALL OUTLINE, HEAT SINK/SLUG, SHRINK PITCH
认证状态：Not Qualified座面最大高度：2.11 mm
最大供电电压 (Vsup)：18 V最小供电电压 (Vsup)：8 V
表面贴装：YES端子形式：GULL WING
端子节距：0.8 mm端子位置：DUAL
宽度：5.4 mmBase Number Matches：1

BA6219BFP-Y-DX 数据手册

 浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第1页浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第2页浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第3页浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第4页浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第5页浏览型号BA6219BFP-Y-DX的Datasheet PDF文件第7页 
Motor driver ICs  
BA6219B / BA6219BFP-Y  
(6) The quality of these products have been carefully  
checked; however, use of the products with applied volt-  
ages, operating temperatures, or other parameters that  
exceed the absolute maximum rating given may result in  
the damage of the IC and the product it is used in. If the  
IC is damaged, the short mode and open modes cannot  
be specified, so if the IC is to be used in applications  
where parameters may exceed the absolute maximum  
ratings, then be sure to incorporate fuses, or other physi-  
cal safety measures.  
(14) If the potential of the output pin sways greatly and  
goes below the potential of ground, the operation of the  
IC may malfunction or be adversely affected. In such a  
case, place a diode between the output and ground, or  
other measure, to prevent this.  
(7) Input pins  
Voltage should never be applied to the input pins when  
the VCC voltage is not applied to the IC. Similarly, when  
VCC is applied, the voltage on each input pin should be  
less than VCC and within the guaranteed range for the  
electrical characteristics.  
(8) Back-rush voltage  
Depending on the ambient conditions, environment, or  
motor characteristics, the back-rush voltage may fluctu-  
ate. Be sure to confirm that the back-rush voltage will not  
adversely affect the operation of the IC.  
(9) Power dissipation  
The power dissipation will fluctuate depending on the  
mounting conditions of the IC and the ambient environ-  
ment. Make sure to carefully check the thermal design of  
the application where these ICs will be used.  
(10) Power consumption  
The power consumption by the IC varies widely with the  
power supply voltage and the output current. Give full  
consideration to the power dissipation rating and the  
thermal resistance data and transient thermal resistance  
data, to provide a thermal design so that none of the rat-  
ings for the IC are exceeded.  
(11) ASO  
Make sure that the output current and supply voltage do  
not exceed the ASO values.  
(12) Precautions for input mode switching  
To ensure reliability, it is recommended that the mode  
switching for the motor pass once through the open  
mode.  
(13) There are no circuits built into these ICs that pre-  
vent in-rush currents. Therefore, it is recommended to  
place a current limiting resistor or other physical counter-  
measure.  
403  
1...34567

下载PDF

与BA6219BFP-Y-DX相关器件

型号 品牌 描述 获取价格 数据表
BA6219BFP-Y-DXE1 ROHM Brush DC Motor Controller, 2.2A, PDSO25, POWER, HSOP-25

获取价格
BA6219BFP-Y-DXE2 ROHM Brush DC Motor Controller, 2.2A, PDSO25, POWER, HSOP-25

获取价格
BA6219BFP-Y-DXT1 ROHM Brush DC Motor Controller, 2.2A, PDSO25, POWER, HSOP-25

获取价格
BA6219BFP-Y-DXT2 ROHM Brush DC Motor Controller, 2.2A, PDSO25, POWER, HSOP-25

获取价格
BA6219BFP-YE1 ROHM BRUSH DC MOTOR CONTROLLER, 2.2A, PDSO27, HSOP-25

获取价格
BA6219BFP-YE2 ROHM BRUSH DC MOTOR CONTROLLER, 2.2A, PDSO25, ROHS COMPLIANT, HSOP-25

获取价格

与BA6219BFP-Y-DX相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证