Pressure sensors
C44 series
B58601E44x5B705
Gauge pressure sensor die C44/1 no back-side glass
Symbols and Terms
1)
Maximum power supply VDD
This is the maximal allowed voltage, which may be applied to the piezoresistive bridge circuit without damage.
2)
Operating temperature range Ta
This is the operating temperature range Ta,min to Ta,max. Because most of the sensor parameters depend on assembling
conditions like glueing, wire bonding etc, the die has to be tested over the operating temperature range by the customer
fully assembled. For design verification and process control, samples, mounted in TDK Sensors standard transducer
packages, are tested over the temperature range of Ta,min to Ta,max
.
3)
Storage temperature range Tst
If the pressure sensor dies are stored in the temperature range Tst,min to Tst,max without applied voltage power supply, this
will not affect the performance of the pressure sensor dies.
4)
5)
6)
Operating pressure range pr
In the operating pressure range 0 to pr,max the pressure sensor die output characteristic is as defined in this specification.
Over pressure pOV
Pressure cycles in the pressure range 0 to pov do not affect the performance of the pressure sensor dies.
Burst pressure pburst
Up to the burst pressure pburst the diaphragm of the sensor die will not be destroyed mechanically. This parameter is
tested at room temperature on samples mounted on an aluminium socket by increasing a test pressure until the sensor is
burst or the maximum test pressure is achieved. Since the burst pressure depends on several assembling conditions,
this parameter has to be verified by the customer with his assembling possibilities.
7)
Operating power supply VDD
The pressure sensor parameters are defined for a power supply voltage of VDD = 5 V. In the operating power supply
voltage range VDD,min to VDD,max the ratiometric parameters r(VDD) like sensitivity, offset voltage and the temperature
coefficient of the offset voltage are defined by:
VDD
(
)
( [ ])
r VDD = r 5 V
[ ]
5 V
8)
9)
Total bridge resistance Rb
The total bridge resistance is defined between pad X5 and X2 (see the dimensional drawing in this data sheet) of the
closed piezoresistive bridge circuit. The total bridge resistance is in a good approximation the output impedance of the
piezoresistive bridge circuit. This parameter is tested completely on a wafer (wafer level test measurement).
Temperature coefficients of resistance Rb and Rb
:
The temperature coefficients of resistance are tested for design verification on samples, mounted in TDK Sensors
standard transducer package over the temperature range Ta,min to Ta,max with TR = 25 °C.
The temperature coefficients of first and second order are defined with the polynomial:
( )
)ꢁ]
Rb T = Rb T = 25°C 1 + αꢀb T − 25°C + βꢀb T − 25°C
(
)[
(
)
(
The coefficients Rb and Rb are calculated using the three measurement points of Rb(T) at Ta,min, TR and Ta,max
Offset voltage V0
The offset voltage V0 is the output voltage Vout(p = 0 bar gauge) at zero gauge pressure and for a bridge voltage power
supply VDD = 5 V. This parameter is tested completely on a wafer (wafer level test measurement).
Since the offset voltage depends on several assembling conditions, this parameter has to be verified by the customer
with his assembling possibilities.
.
10)
11)
Temperature coefficients of offset voltage TCV0
The temperature coefficients of offset voltage are defined for a bridge voltage power supply VDD = 5 V.
These parameters strongly depend on assembly conditions like gluing, wire bonding etc.
The temperature coefficients of offset voltage are tested for design verification on samples, mounted in TDK Sensors
standard transducer package over the temperature range Ta,min to Ta,max with TR = 25 °C.
Therefore TCV0+ and TCV0- are defined for the measurement temperature range by:
(
)
(
)
ꢉꢊꢄ ꢁꢋ°ꢌ
ꢄ ꢇꢈ
ꢉꢊꢄ ꢁꢋ°ꢌ
ꢄ ꢇꢈ
ꢃ
ꢃ
ꢆ
a,max
ꢆ
ꢆ
a,min
ꢆ
TCVoꢂ =
TCVoꢊ =
ꢄ
ꢈ
ꢊꢁꢋ°ꢌ
ꢄ
ꢈ
ꢊꢁꢋ°ꢌ
a,min
ꢅꢅ
a,max
ꢅꢅ
Since the TCV0 depends on several assembling conditions, this parameter has to be verified by the customer with his
assembling possibilities.
TPS PRS SD PD
2021-08-12
Please read Cautions and warnings and
Page 5 of 10
Important notes at the end of this document.
5秒后页面跳转
LM317T数据手册解读：产品特性、应用、封装与引脚详解
一文带你了解?DB3二极管好坏判断、参数信息、替代推荐
LM358DR数据手册：引脚说明、电气参数及替换型号推荐
OP07CP数据手册解读：引脚信息、电子参数
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
