Pressure sensors
C28 series
Gauge pressure sensor die for front side pressure applications
Symbols and Terms
1)
Maximum power supply VDD
This is the maximal allowed voltage, which may be applied to the piezoresistive bridge circuit without damage.
2)
Operating temperature range Ta
This is the operating Temperature range Ta,min to Ta,max. Because most of the sensor parameters depend on assembling
conditions like gluing, wire bonding etc, the die has to be tested over the operating temperature range by the customer
fully assembled. For design verification and process control samples, mounted on a TO39 base are tested over a
reduced measuring temperature range of Tmeas,min to Tmeas,max
.
3)
Storage temperature range Tst
If the pressure sensor dies are stored in the temperature range Tst,min to Tst,max without applied voltage power supply, this
will not affect the performance of the pressure sensor dies.
4)
5)
6)
Operating pressure range pr
In the operating pressure range 0 to pr,max the pressure sensor die output characteristic is as defined in this specification.
Over pressure pOV
Pressure cycles in the pressure range 0 to pov do not affect the performance of the pressure sensor dies.
Burst pressure pberst
Up to the burst pressure pberst the diaphragm of the sensor die will not be destroyed mechanically. This parameter is
tested at room temperature on samples mounted on an aluminium socket by increasing the applied pressure until the
diaphragm is destroyed.
7)
Operating power supply VDD
The pressure sensor parameters are defined for a power supply voltage of VDD = 5 V. In the operating power supply
voltage range VDD,min to VDD,max the ratiometric parameters r(VDD) like sensitivity, offset voltage and the temperature
coefficient of the offset voltage are defined by:
VDD
r
VDD = r(5[V])
( )
5[V]
8)
9)
Total bridge resistance RS
The total bridge resistance is defined between pad X5 and X2, X3 (see the dimensional drawing in this data sheet) of the
closed piezoresistive bridge circuit. The total bridge resistance is in a good approximation the output impedance of the
piezoresistive bridge circuit. This parameter is tested completely on a wafer (wafer level test measurement).
Temperature coefficients of resistance αRs and βRs
The temperature coefficients of resistance are tested for design verification on samples, mounted on a TO39 base
over a reduced temperature range Tmeas min = –20 °C to Tmeas max = 80 °C with TR = 25 °C.
:
,
,
The temperature coefficients of first and second order are defined with the polynomial:
2
R (T)=R (T=25°C ) 1+α
S
Rs T−25°C
+β
Rs T−25°C
S
The coefficients αRs and βRs are calculated using the three measurement points of Rs(T) at Tmeas,min, TR and Tmeas,max
.
10)
11)
Offset voltage V0
The offset voltage V0 is the output voltage Vout(p = 0 bar gauge) at zero gauge pressure and for a bridge voltage power
supply VDD = 5 V. This parameter is tested completely on a wafer (wafer level test measurement).
It should be noted that this parameter may be influenced by assembly.
Temperature coefficient of offset voltage TCV0
The temperature coefficients of offset voltage are defined for a bridge voltage power supply VDD = 5 V.
These parameters strongly depend on assembly conditions like gluing, wire bonding etc.
The temperature coefficients of offset voltage are tested for design verification on samples, mounted on a TO39 base
over a temperature range Tmin = –40 °C to Tmax = 135 °C.
Therefore TCV0+ and TCV0- are defined for the measurement temperature range by:
Vo(Tmax ) − Vo(25°C)
Tmax − 25°C
Vo(Tmin ) − Vo(25°C)
Tmin − 25°C
TCVo+
=
TCVo− =
AS SEN PD
2009-08-03
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 8
5秒后页面跳转
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
CD4052资料手册参数详解、引脚配置说明
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
