ATA6832

更新时间： 2024-02-18 08:50:24

品牌	Logo	应用领域
爱特美尔 - ATMEL		驱动器
页数	文件大小	规格书
17页	331K
描述
High Temperature Triple Half-bridge Driver with SPI and PWM

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

ATA6832 技术参数

是否Rohs认证：	符合	生命周期：	Transferred
包装说明：	,	Reach Compliance Code：	compliant
风险等级：	5.68	Base Number Matches：	1

ATA6832 数据手册

ATA6832

3.4

Overtemperature Protection

If the junction temperature of one or more output stages exceeds the thermal prewarning thresh-

old, T_{jPW set}, the temperature prewarning bit (TP) in the output register is set. When the

temperature falls below the thermal prewarning threshold, T_{jPW reset}, the bit TP is reset. The TP

bit can be read without transferring a complete 16-bit data word. The status of TP is available at

pin DO with the falling edge of CS. After the microcontroller has read this information, CS is set

high and the data transfer is interrupted without affecting the status of input and output registers.

If the junction temperature of an output stage exceeds the thermal shutdown threshold, T_{jswitch off}

the affected output is disabled and the corresponding bit in the output register is set to low. Addi-

tionally, the overload detection bit (OVL) in the output register is set. The output can be enabled

again when the temperature falls below the thermal shutdown threshold, T_{jswitch on}, and the SRR

bit in the input register is set to high. The hysteresis of thermal prewarning and shutdown thresh-

old avoids oscillations.

3.5

Short-circuit Protection

The output currents are limited by a current regulator. Overcurrent detection is activated by writ-

ing a high to the overcurrent shutdown bit (OCS) bit in the input register. When the current in an

output stage exceeds the overcurrent limitation and shut-down threshold, it is switched off, fol-

lowing a delay time (t_dSd). The over-load detection bit (OVL) is set and the corresponding status

bit in the output register is set to low. For OCS = low, the overcurrent shutdown is inactive and

the OVL bit is not set by an overcurrent. By writing a high to the SRR bit in the input register the

OVL bit is reset and the disabled outputs are enabled.

3.6

3.7

Inhibit

The SI bit in the input register has to be set to zero to inhibit the ATA6832.

In this state, all output stages are then turned off but the serial interface remains active. The out-

put stages can be reactivated by setting bit SI to “1”.

PWM Mode

The common input for all six outputs is pin PWM (Figure 3-2). The selection of the outputs,

which are controlled by PWM, is done by input data register PLx or PHx. In addition to the PWM

input register, the corresponding input registers HSx and LSs have to be set.

Switching the high side outputs is possible up to 25 kHz, low side switches up to 8 kHz.

Figure 3-2. Output Control by PWM

Bit LSx/HSx

Pin OUTx

Bit PLx/PHx

Pin PWM

4951D–AUTO–08/09

1...4 5 678 9 10...17

下载PDF

与ATA6832相关器件

型号	品牌	描述	获取价格	数据表
ATA6832_08	ATMEL	High Temperature Triple Half-bridge Driver with SPI and PWM	获取价格
ATA6832_09	ATMEL	High Temperature Triple Half-bridge Driver with SPI and PWM	获取价格
ATA6832_10	ATMEL	Three Half-bridge Outputs Formed by Three High-side and Three Low-side Drivers	获取价格
ATA6832C	MICROCHIP	Fully protected triple half bridge driver designed in SOI technology that allows especiall	获取价格
ATA6832C-PIQW	MICROCHIP	PWM Based Peripheral Driver	获取价格
ATA6832C-PIQW	ATMEL	PWM Based Peripheral Driver,	获取价格

与ATA6832相关文章

MC34063开关稳压器：全面参数解析与设计指南
2024-05-08

3
CC2530无线微控制器：资料手册参数分析
2024-05-08

8
NE5532双低噪声运算放大器：资料手册参数分析
2024-05-07

13
74LS138 3-to-8线解码器/多路复用器：资料手册参数分析
2024-05-07

18

产品中心

服务支持

精选活动

关于我们

帮助中心

ATA6832

ATA6832 技术参数

ATA6832 数据手册

与ATA6832相关器件

与ATA6832相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

ATA6832

ATA6832 技术参数

ATA6832 数据手册

与ATA6832相关器件

与ATA6832相关文章

您还可以找

您在本页遇到什么问题？