Preliminary
AS2520/21/20B/21B
The acoustic stability is provided as follows:
20 to 50 mA or 45 to 75 mA depending on selected
range.
When the volume is increased, e.g. by 10 dB, the
receive gain maintains the same as long as no
receive signal is applied. Applying a receive signal
will cause a 10 dB increase of the receive gain and a
corresponding decrease of the transmit gain. This
squelch function improves the signal-to-noise ratio.
Loudhearing
The loudhearing mode is enabled when HS and LE
are high. In order to prevent acoustic coupling
between the handset microphone and the
loudspeaker, the AS252x incorporate an anti-Larsen
circuit.
In other words, a certain increase of the volume
introduces a similar amount of dynamic voice
switching, controlled by the receive signal, also in the
handset mode.
The anti-Larsen circuit decreases the gain of the
loudspeaker amplifier when a microphone signal is
applied. If no signal is applied from the microphone,
the loudspeaker amplifier is at its full gain.
Sidetone
Anti-Clipping (not AS2520B/21B)
A good sidetone cancellation is achieved by using
the following equation:
The anti-clipping circuit is activated in loudhearing
and handsfree mode. The circuit prevents harsh
distortion at very high signal levels.
ZBAL/ZLINE = R5/R1
The sidetone cancellation signal is applied to the
STB input.
Furthermore, the circuit assures that the integrity of
the whole telephone circuit is maintained under
extreme load conditions, since it prevents that the
supply voltage drops below a certain minimum level.
By using two separate Wheatstone Bridges for return
loss and sidetone cancellation it is very easy to
calculate the sidetone balance network (see figure 4).
The attack time is fast (120 µs/6 dB) for preventing
harsh distortion when the amplitude rapidly
increases. For avoiding chopper effects and to
assure low distortion, the decay time is longer,
approx. 128 ms/6 dB.
This unique configuration provides
a sidetone
cancellation less sensitive to tolerances on the
external balance network and totally independent of
the ac impedance and its tolerances.
A good and stable sidetone cancellation improves the
handsfree function considerably and ensures a safe
margin against acoustic instability under all
circumstances.
When the anti-clipping circuit has been activated by a
large receive signal, the channel control will increase
the Tx gain corresponding to the reduction in Rx gain
caused by the anti-clipping.
Handsfree
R1
30 ohm
ZLINE
The handsfree function allows voice communication
without using the handset (full 2-way speaker phone).
Two voice controlled attenuators prevent acoustic
coupling between the loudspeaker and the
microphone.
R5
300 ohm
ZBAL
Figure 4: Sidetone Bridge
A conventional voice switching circuit has a channel
control with three states, namely idle, transmit or
receive. In idle state, when no signal is applied, both
the transmit and the receive channels are attenuated
by approx. 20 dB to keep the total loop gain below 0
dB.
Furthermore, the dual Wheatstone bridge makes it
very simple to adapt the circuit to different PTT
requirements as these two parameters (return loss
and sidetone balance) are independent of each
other.
Line Loss Compensation
When a signal is applied to the microphone, the
circuit switches to transmit state, i.e. the gain in the
transmit channel is increased and the gain in the
receive channel is decreased accordingly. And vice
versa when a receive signal is applied.
The line loss compensation (Rx and Tx AGC
controlled by the line current) is a pin option. When it
is activated, the transmit and receive gains are
changed by -6 dB in 1 dB steps at line currents from
Rev. 5.1
Page 6
May 1999
5秒后页面跳转
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
CD4052资料手册参数详解、引脚配置说明
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
