5秒后页面跳转
AS1582 PDF预览

AS1582

更新时间: 2024-01-25 23:55:48
品牌 Logo 应用领域
西伯斯 - SIPEX 稳压器射频微波
页数 文件大小 规格书
4页 114K
描述
3A Ultra Low Dropout Voltage Regulator Fast Response, Adjustable & Fixed

AS1582 技术参数

是否Rohs认证:不符合生命周期:Transferred
Reach Compliance Code:unknown风险等级:5.67
Is Samacsys:N可调性:ADJUSTABLE
标称回动电压 1:0.5 VJESD-609代码:e0
最大电网调整率 (%/V):0.07最大负载调整率 (%):0.4%
输出次数:1端子数量:5
工作温度TJ-Max:125 °C工作温度TJ-Min:
最大输出电流 1:3 A最大输出电压 1:5 V
最小输出电压 1:1.25 V封装主体材料:PLASTIC/EPOXY
封装等效代码:SIP5,.1,67TB认证状态:Not Qualified
子类别:Other Regulators表面贴装:NO
技术:BIPOLAR端子面层:Tin/Lead (Sn/Pb)
端子节距:1.7 mm端子位置:SINGLE
Base Number Matches:1

AS1582 数据手册

 浏览型号AS1582的Datasheet PDF文件第1页浏览型号AS1582的Datasheet PDF文件第2页浏览型号AS1582的Datasheet PDF文件第4页 
AS1582  
PIN DESCRIPTION  
1. Sense = Allows Kelvin sense of VOUT at the load. (Positive side of the reference voltage of the  
device).  
2. ADJ = Negative side of the reference voltage for the device. Adding a small bypass capacitor  
from the ADJ pin to ground will improve the transient response.  
3.  
4.  
V
V
OUT = Power output of the device.  
CTRL = Supply pin for the control circuitry of the device. The current flow into this pin will be  
about 1% of the output current. VCTRL must be between 1.0V and 1.3V greater than the output  
voltage for the device to regulate.  
5. VIN = Output load current is supplied through this pin. VIN must be between 0.1V and 0.8V  
greater than the output voltage for the device to regulate.  
BLOCK DIAGRAM  
(4) VCTRL  
VIN (5)  
S.O.A  
CURRENT  
LIMIT  
LIMIT  
AMPLIFIER  
VOUT (3)  
SENSE (1)  
ADJ (2)  
SENSE  
THERMAL OVERLOAD  
VOLTAGE  
REGULATION  
AMPLIFIER  
VREF  
APPLICATIONS NOTES  
The AS1582 is designed as a high performance and low cost  
solution for application requiring a lower dropout than  
traditional NPN regulators.  
Adjustable Regulator Design  
1.25V reference voltage is being developed between the  
SENSE pin and the ADJ pin of the AS1582. Adding two  
external resistors (see fig 1.) will allow setting the output  
voltage from 1.25V to 6V. R1 is chosen so that this current is  
specified minimum load current of 10mA. R2 is given by the  
formula: VOUT = VREF (1+ R2/R1) + IADJ (R2). The current  
flowing from the ADJ pin is typically 50µA. This ADJ pin  
contributes to the final VOUT but is usually neglected.  
Connecting the sense pin to the top of the resistor divider will  
improve load regulation.  
The AS1582 uses a separate input voltage VCTRL (VCTRL  
V
OUT+ 1.3V) to minimize the dropout voltage. This allows the  
2.5V power for the load to come from a 3.3V system supply.  
As added benefit this will reduce the heat dissipation, and  
lower heatsink and cooling fan cost. A typical application  
would use 5V for Vin and 3.3V for VCTRL from a motherboard  
power supply to provide a nominal 2.5V output. Using the  
sense pin allows to Kelvin measure the output, reducing  
resistive-associated errors.  
The AS1582 can power the 2.5V core voltage for  
microprocessors such as Pentium, P55C, AMD5k86  
and K6and the IBM PowerPC603EV and 604EV  
processors.  
Lowering Noise  
Using the SENSE pin to Kelvin the load will increase accuracy  
of the output voltage during load regulation. For the fixed  
voltage devices, adding a capacitor at the GND pin will  
improve transient response. This capacitor is chosen in the  
range of 1µF to 0.1µF and will depend on the amount of  
output capacitance in the system.  
*The reduction of heat dissipation is a result of the increase of the regulator  
efficiency (efficiency = VOUT / VIN).  
Rev. 10/2/00  

与AS1582相关器件

型号 品牌 描述 获取价格 数据表
AS1582T SIPEX 3A Ultra Low Dropout Voltage Regulator Fast Response, Adjustable & Fixed

获取价格

AS1582T-2.5 ETC Analog IC

获取价格

AS1582T-2.8 ETC Analog IC

获取价格

AS1582T-3.3 ETC Analog IC

获取价格

AS1582T-X SIPEX 3A Ultra Low Dropout Voltage Regulator Fast Response, Adjustable & Fixed

获取价格

AS1582U SIPEX 3A Ultra Low Dropout Voltage Regulator Fast Response, Adjustable & Fixed

获取价格