AMIS-40615
LIN Transceiver with 3.3V Voltage Regulator
Data Sheet
Table 4: Mode Selection
Mode
Vcc
RxD
INH
LIN
30kΩ on LIN
Note
Normal - Slope
On
Low = dominant state
High = recessive state
Low = dominant state
High = recessive state
Low after LIN wakeup, high otherwise
Clamped to Vcc
High if STB = High during state
transition; floating otherwise
High if STB = High during state
transition; floating otherwise
Floating
Normal slope
On
(1)
Normal - Low Slope
On
Low slope
On
(2)
(3)
Stand-by
Sleep
On
Off
Off
Off
Off
Off
Floating
Notes:
1.
2.
The normal slope mode is entered when pin EN goes high while TxD is in high state during EN transition.
The low slope mode is entered when pin EN goes high while TxD is in low state during EN transition. LIN transmitter gets on only after TxD returns to high after the
state transition.
3.
The stand-by mode is entered automatically after power-up.
7.2.1. Normal Slope Mode
In normal slope mode the transceiver can transmit and receive data via LIN bus with speed up to 20kBaud. The transmit data stream of
the LIN protocol is present on the TxD pin and converted by the transmitter into a LIN bus signal with controlled slew rate to minimize
EMC emission. The receiver consists of the comparator that has a threshold with hysteresis in respect to the supply voltage and an
input filter to remove bus noise. The LIN output is pulled high via an internal 30kΩ pull-up resistor. For master applications it is needed
to put an external 1kΩ resistor with a serial diode between LIN and Vbb (or INH). See Figure 2. The mode selection is done by
EN=HIGH when TxD pin is high. If STB pin is high during the stand-by-to-normal slope mode transition, INH pin is pulled high.
Otherwise, it stays floating.
7.2.2. Low Slope Mode
In low slope mode the slew rate of the signal on the LIN bus is reduced (rising and falling edges of the LIN bus signal are longer). This
further reduces the EMC emission. As a consequence the maximum speed on the LIN bus is reduced up to 10kBaud. This mode is
suited for applications where the communication speed is not critical. The mode selection is done by EN=HIGH when TxD pin is low. In
order not to transmit immediately a dominant state on the bus (because TxD=LOW), the LIN transmitter is enabled only after TxD
returns to high. If STB pin is high during the standby-to-low slope mode transition, INH pin is pulled high. Otherwise, it stays floating.
7.2.3. Stand-by Mode
The stand-by mode is always entered after power-up of the AMIS-40615. It can also be entered from normal mode when the EN pin is
low and the stand-by pin is high. From sleep mode it can be entered after a local wake-up or LIN wakeup. In stand-by mode the Vcc
voltage regulator for supplying external components (e.g. a microcontroller) stays active. Also the LIN receiver stays active to be able to
detect a remote wake-up via bus. The LIN transmitter is disabled and the slave internal termination resistor of 30kΩ between LIN and
Vbb is disconnected in order to minimize current consumption. Only a pull-up current source between Vbb and LIN is active.
7.2.4. Sleep Mode
The sleep mode provides extreme low current consumption. This mode is entered when both EN and STB pins are low coming from
normal mode. The internal termination resistor of 30kΩ between LIN and Vbb is disconnected and also the Vcc regulator is switched off
to minimize current consumption.
7.2.5. Wake-up
AMIS-40615 has two possibilities to wake-up from sleep or stand-by mode (see Figure 4):
• Local wake-up: enables the transition from sleep mode to stand-by mode.
• Remote wake-up via LIN: enables the transition from sleep- to stand-by mode and can be also detected when already in standby
mode.
A local wake-up is only detected in sleep mode if a transition from low to high or from high to low is seen on the wake pin.
AMI Semiconductor – March 2007, M-20544-001
7
www.amis.com
5秒后页面跳转
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
74HC573三态非易失锁存器(Latch)资料手册参数分析
MAX3232 RS-232电平转换器资料手册参数分析
MAX485 RS-485/RS-422收发器资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
