ADSP-21367/ADSP-21368/ADSP-21369
Digital audio interface (DAI) includes eight serial ports, four
precision clock generators, an input data port, an S/PDIF
transceiver, an 8-channel asynchronous sample rate con-
verter, and a signal routing unit
Digital peripheral interface (DPI) includes three timers, two
UARTs, two SPI ports, and a two wire interface port
Outputs of PCG's C and D can be driven on to DPI pins
Eight dual data line serial ports that operate at up to
50M bits/s on each data line—each has a clock, frame sync,
and two data lines that can be configured as either a
receiver or transmitter pair
TDM support for telecommunications interfaces including
128 TDM channel support for newer telephony interfaces
such as H.100/H.110
Up to 16 TDM stream support, each with 128 channels per
frame
Companding selection on a per channel basis in TDM mode
Input data port, configurable as eight channels of serial data
or seven channels of serial data and up to a 20-bit wide
parallel data channel
Signal routing unit provides configurable and flexible con-
nections between all DAI/DPI components
2 muxed flag/IRQ lines
KEY FEATURES—PROCESSOR CORE
At 333 MHz (3 ns) core instruction rate, the processors per-
form 2 GFLOPS/666 MMACS
2M bit on-chip, SRAM (0.75M bit in blocks 0 and 1, and
0.25M bit in blocks 2 and 3) for simultaneous access by the
core processor and DMA
6M bit on-chip, mask-programmable ROM (3M bit in block 0
and 3M bit in block 1)
Dual data address generators (DAGs) with modulo and bit-
reverse addressing
Zero-overhead looping with single-cycle loop setup, provid-
ing efficient program sequencing
Single-instruction, multiple-data (SIMD) architecture
provides:
Two computational processing elements
Concurrent execution
Code compatibility with other SHARC family members at
the assembly level
Parallelism in buses and computational units allows: single
cycle executions (with or without SIMD) of a multiply
operation, an ALU operation, a dual memory read or
write, and an instruction fetch
Transfers between memory and core at a sustained
6.4G bytes/s bandwidth at 333 MHz core instruction rate
1 muxed flag/timer expired line /MS pin
1 muxed flag/IRQ /MS pin
INPUT/OUTPUT FEATURES
DEDICATED AUDIO COMPONENTS
DMA controller supports:
S/PDIF-compatible digital audio receiver/transmitter sup-
ports EIAJ CP-340 (CP-1201), IEC-958, AES/EBU standards
Left-justified, I2S, or right-justified serial data input with
16-, 18-, 20- or 24-bit word widths (transmitter)
Four independent asynchronous sample rate converters
(SRC). Each converter has separate serial input and output
ports, a de-emphasis filter providing up to –140 dB SNR
performance, stereo sample rate converter (SRC) and sup-
ports left-justified, I2S, TDM, and right-justified modes and
24, 20, 18, and 16 audio data word lengths
34 zero-overhead DMA channels for transfers between
internal memory and a variety of peripherals
32-bit DMA transfers at peripheral clock speed, in parallel
with full-speed processor execution
32-bit wide external port provides glueless connection to
both synchronous (SDRAM) and asynchronous memory
devices
Programmable wait state options: 2 SCLK to 31 SCLK cycles
Delay-line DMA engine maintains circular buffers in exter-
nal memory with tap/offset-based reads
SDRAM accesses at 133 MHz and asynchronous accesses at
66 MHz
Shared-memory support allows multiple DSPs to automat-
ically arbitrate for the bus and gluelessly access a
common memory device
Shared memory interface (ADSP-21368 only) support
provides:
Glueless connection for scalable DSP multiprocessing
architecture
Distributed on-chip bus arbitration for parallel bus
Connect of up to four ADSP-21368 processors and global
memory
Pulse-width modulation provides:
16 PWM outputs configured as four groups of four outputs
supports center-aligned or edge-aligned PWM waveforms
ROM-based security features include:
JTAG access to memory permitted with a 64-bit key
Protected memory regions that can be assigned to limit
access under program control to sensitive code
PLL has a wide variety of software and hardware multi-
plier/divider ratios
Dual voltage: 3.3 V I/O, 1.2 V or 1.3 V core
Available in 256-ball SBGA and 208-lead MQFP packages (see
Ordering Guide on Page 56)
Four memory select lines allow multiple external memory
devices
Rev. A
|
Page 2 of 56
|
August 2006
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
